Ultrasonic welding is a solid-state welding technique that can bond materials at a relatively low temperature and pressure. In this study, steel/steel and steel/Ni combinations were successfully bonded by ultrasonic welding, and the development of the bonding interface was examined. The bonding strength was obtained by a lap shear test and increased with welding time, as did the fraction of bonded area observed by SEM. The bonding process sequence was investigated by SEM and electron backscatter diffraction (EBSD) analysis of a cross-section at the bonding interface. It was revealed that abrasion is caused by oscillation to form small particles consisting of steel and Ni and that the particles are grown and subsequently flattened with welding time. Bonding is achieved by the flattened particles spreading along the bonding interface without any voids.
A crystallographic analysis was conducted of the upper bainite nucleated at the austenite grain boundary in Fe-0.6C-0.8Mn-1.8Si (in mass %) steel by the EBSD analysis. The effect of the character of the prior austenite grain boundary (PAGB) on the formation of upper bainite was investigated from several perspectives: PAGB plane, grain boundary energy, and so on. BFs form on both sides of the high-angle PAGBs, while BFs do not form at twin boundaries. It is suggested one of the reasons for the suppression of BF formation at twin boundaries is the lower grain boundary energy. At high-angle grain boundaries, there is no difference in the potency for BFs’ nucleation between the tilt-like PAGBs and twist-like PAGBs, and the formation of BF is not affected by the angle between the rotation axis, the PAGB plane, and grain boundary energy. The variant selection of BFs was investigated. The BFs pair, whose misorientation across the PAGB is small, is formed preferentially. When several variant pairs can form having small misorientation across the PAGB, the variant pair that can reduce the elastic strain energy preferentially forms to accommodate the shape strain.
Three-dimensional microstructures of bainitic ferrites and prior austenite grains (PAGs) were observed in the initial stage of upper bainite transformation by using a serial sectioning technique and orientation analysis by electron back scattering diffraction (EBSD). The formation site of the bainitic ferrites was quantitatively evaluated by three-dimensional observation. It was revealed that the bainitic ferrites mainly form at the planes rather than the edges of prior austenite grain boundaries (PAGBs) and form on both sides of the PAGB plane. The effect of the orientation of the PAGs on the formation of the bainitic ferrites was also investigated. The bainitic ferrite has a small misorientation with the bainitic ferrite in the adjacent PAG across the PAGB. It is suggested that the reason for the formation of bainitic ferrite at the planes rather than edges of PAGBs is because it is difficult for bainitic ferrite to have a small misorientation with the bainitic ferrites in adjacent PAGs at edges.
We employed the high-resolution digital image correlation study to investigate the plastic deformation of low-carbon lath martensite. The strain localization bands were mainly categorized into two types: boundary slips and intra-block deformation. Misorientation angle and inclination angle with respect to loading direction primarily determines the slip activation at boundaries. The competitive relationship between the activation of in-lath-plane and out-of-lath-plane slip systems follows the Schmid effect. The in-lath-plane slip systems were only activated in blocks with high in-lath Schmid factor (SF) value. The out-of-lath-plane slip systems were activated only when its SF is much higher than the maximum in-lath SF, offsetting the effect of the higher critical resolved shear stress (CRSS) for in-lath-plane slip systems. Moreover, the block morphology also affects the slip activation behaviour: in-lath-plane slip systems in columnar blocks were preferentially activated due to both crystallographic dynamics and strain accommodation. In contrast, out-of-plane slip systems were only observed in equiaxed blocks where the boundary effect is weakened.
Crystallographic analysis was carried out on acicular ferrites (AFs) of steel that nucleated on B1-type compounds embedded in steels during the isothermal transformation from austenite (γ) to ferrite (α), and the orientation relationship between α, γ, and the compounds and the AF formation behavior were correlated by varying the B1-type compound, steel, and transformation temperature. The results demonstrated that all the AFs satisfy the Kurdjumov–Sachs orientation relationship with the prior γ, and in addition, some of the AFs have specific low-index orientation relationships with the B1-type compounds and nucleate earlier than others. Among the specific low-index orientation relationships, furthermore, AFs satisfying the Baker–Nutting orientation relationship, which gives the lowest interfacial energy between α and a compound, nucleate preferentially.
20 May 2026 in Journal of Materials Research and Technology