30 August 2018 in IEEE Transactions on Energy Conversion
With the development of more electric aircraft (MEA), higher demand for electrical energy is put forward in generation systems. The constant speed drive is eliminated in variable frequency AC (VFAC) generation systems, which makes integrated starter-generator (SG) can be realized. Considering the inherent defects of wound rotor synchronous SG systems, such as the complex starting excitation methods and rotating rectifiers, this paper proposes a VFAC SG system based on hybrid excitation synchronous machines (HESMs) for aircraft applications. The key of HESM-based VFAC SG system is to regulate the field current in such a way that three major modes of VFAC SG system operation for aircraft applications, namely, engine starting operation, transition mode, and generating operation, can be achieved effectively. The simulation model of HESM-based VFAC SG system is built and analyzed. A prototype HESM-based VFAC SG system has been designed and developed for experimental verification. The starting operation, transition mode and generating operation of the prototype HESM-based VFAC SG system are implemented. The feasibility of HESMs to VFAC SG system for safety-critical aircraft applications has been validated.
25 July 2018 in IEEE Transactions on Magnetics
This paper proposes and analyzes the design philosophies of the single-phase main exciter (ME) for an aircraft wound-rotor synchronous machine and investigates its operating characteristics in both generating and starting modes. The fundamental structure and starting–generating system are discussed. The load features of single-phase ME are summarized. The ME has the characteristics of linear current amplifier and approximately constant current source the generating mode, which can be used in the wide range of working temperature. Detailed waveforms and finite-element analysis verify that excitation current $I_{\mathrm {ef}}$ is almost irrelevant to speed but in direct proportion to frequency in the starting mode. Besides, simulated data indicate that the energy transferring efficiency between ME stator and rotor can reach about 55% by the single-phase ac excitation method. Finally, the experimental verification is carried out, and the simulated and experimental data and waveforms of single-phase ME agree well with each other.
24 April 2017 in IEEE Transactions on Magnetics
In this paper, a novel modeling method for hybrid excitation synchronous machines (HESMs) with radial/axial flux paths via magnetic equivalent circuit (MEC) is proposed. 3-D finite-element analysis (FEA) is essential when analyzing a machine with radial/axial flux paths due to the asymmetry in the axial direction. However, 3-D FEA is computationally expensive and time-consuming, especially during the preliminary design stage. The proposed modeling method is analyzed and validated based on an HESM with magnetic shunting rotor. The fundamental structure and working principle of the HESM with magnetic shunting rotor are introduced. On the basis of 3-D structure, an MEC considering saturation and leakage flux distribution is built and illustrated, as well as field analysis is performed. A 2-D equivalent finite-element model via MEC is built and illustrated. A prototype HESM with magnetic shunting rotor has been designed by the proposed modeling method and developed for experimental verification. With the proposed modeling method, the computational efficiency is significantly improved in the design stage. The proposed modeling method is verified by the good agreement between the predicted and measured results.
21 June 2017 in IEEE Transactions on Magnetics
In this paper, a new shaded-pole main exciter (ME) with additional short-circuited coils for aircraft three-stage starter-generator (SG) is proposed and investigated. The basic structure, winding configurations, operating principle and start system structure of the presented shaded-pole ME are illustrated in detail. The comparative study between the original ME and the shaded-pole ME with respect to the starting mode performances is conducted by 2D finite element method (FEM). A prototype SG with original ME has been developed, and the experimental results are essentially consistent with the simulation results by the FEM utilized in the predictions in this paper. Simulation data and waveforms verify that the proposed shaded-pole ME is a good candidate for aircraft machines to satisfy the dual function of starter and generator.
22 February 2023 in IEEE Transactions on Transportation Electrification
This paper proposes an active field current tracking (AFCT) control strategy for pulse width modulation (PWM) rectifier, which can remarkably enhance the system’s dynamic performance of wound rotor synchronous starter/generator (WRSSG) system when the load changes. WRSSG system uses a PWM converter in the aero-engine starting process and can reuse the power circuit as a PWM rectifier for high-voltage direct current (HVDC) power generation, thus simplifying the system structure, volume, and weight. The mathematic model of WRSSG system with PWM rectifier is introduced. Based on the system model, the PI controller of armature current loop is designed. The nonlinear PI controller of excitation voltage loop is also illustrated. A 15kW WRSSG system based on PWM rectifier is implemented. The AFCT control strategy and its high dynamic performance are verified by experiments. The simple system structure and distinguished dynamic performance of PWM rectifier with AFCT control can make the WRSSG system more competitive in aircraft applications.
31 January 2024 in IEEE Transactions on Industrial Electronics
This article focuses on analyzing and evaluating the demagnetization behavior of Halbach rotor permanent magnet synchronous machines. An indicator related to the dq -axis current namely I dmag representing the severity of the demagnetization is proposed based on the analysis of a finite-element (FE) model. The influence of transient symmetrical short-circuit (SSC) current is considered during the evaluation of the magnets’ magnetization status. Analysis based on the derived analytical solution proved that ignoring the magnetic saturation caused by the transient SSC current will cause significant inaccuracy in the calculation of I dmag . To improve the calculation efficiency and accuracy, a hybrid model combining the equivalent circuit model, several FE cases, and an analytical mapping model is proposed. The procedures for building the hybrid model are elaborated and its accuracy is verified by time-stepping FE analysis. The proposed model can complete the calculation of one case within 20 s whereas conventional FE analysis typically takes over 10 min. Finally, the accuracy of the FE model is verified by experiments on a manufactured prototype. With this proposed model, both the worst demagnetization scenario over the entire operating range and the maximum acceptable PM temperature at a given speed can be identified. The derived temperature boundary will be used to guide the cooling design of the machine.