The study discusses steady‐state double‐diffusive convective heat and mass transfer (HMT) in a square enclosure containing a clockwise rotating adiabatic cylinder located in the center of the enclosure. The model is a 2‐D square enclosure. The left vertical wall of the enclosure is the higher concentrated‐heated wall, the right is the lower concentrated‐cold wall, T while the cylinder and the horizontal walls of the enclosure are thermally insulated with zero‐mass flux. The descriptive equations were solved by the finite element method for . The implications of cylinder size , cylinder rotational‐speed , Lewis number , buoyancy ratio , and Richardson number on concentration, streamlines, and isotherms are reported. Furthermore, the responses of HMT to the parameters of interest were presented in terms of Nusselt and Sherwood numbers. Results showed that while increasing both the cylinder size and the rotational speed of the cylinder were found to augment both heat and mass transfer, the maximum heat and mass transfer occurred at of the concentrated‐heated wall length, and a critical buoyancy ratio of , for which both HMT were maximized was established. Finally, both HMT diminished as Ri increased. This study provides a pathway for performance improvement in micro‐chip‐cooling in the electronic industry, drying technology, and heat exchangers. The impacts of cylinder rotation and size on HMT for the configuration investigated had not been previously investigated. Furthermore, the study established a critical buoyancy ratio value that ensures maximum heat and mass transfer enhancements.
The transportation of fluids within the petroleum industry presents significant challenges, primarily due to the high cost and energy demand of current systems. These challenges are compounded when transporting multiple fluids, often necessitating separate pipelines or complex flushing procedures between different products. To address these issues, this research explored the feasibility of utilising a concentric piping system for transporting methane and diesel. The governing equations were formulated, and a 15 m-long concentric pipe prototype was modelled using ANSYS Fluent, a computational fluid dynamics (CFDs) software, to simulate two-fluid flow. To accurately capture turbulence effects, the standard K- ϵ turbulence model was employed, with no-slip boundary conditions applied to the pipe walls. The simulations generated results analysing velocity profiles, pressure drops (PDs), and other flow characteristics within a velocity range of 25–40 m s −1 . Findings indicated that the flow became thermally and hydrodynamically fully developed at 6 m downstream of the inlet. Additionally, the pressure decreased monotonically along the length of the pipe in the concentric configuration. At an inlet velocity of 25 m s −1 , the diesel’s temperature change over this region was minimal, whereas methane experienced significant temperature variations. Under the specified thermal boundary conditions, the average velocity of diesel is approximately 1.14 times the mainstream velocity, while methane exhibits more variable flow behaviour. The observed temperature ranges stay well below the autoignition points of methane (537 °C) and diesel (250 °C), indicating that the transportation of fluids via the proposed concentric system is feasible.
30 March 2025 in Al-Qadisiyah Journal for Engineering Sciences
Researchers and the energy industry are currently focusing their efforts on optimizing the effectiveness of vertical-axis wind turbines (VAWT) to cut down on the reliance on energy supply from fossil fuels which releases gases that are toxic to the environment. As such, several methods have been applied, including increasing the velocity and modification of both the trailing and leading edges of the aerofoil. In the present investigation, numerical studies of the flow on the wind turbine blades with a NACA0015 airfoil section equipped with and without tubercles on the trailing edge were conducted using ANSYS Fluent. A computational domain of 2000mm by 35000mm was employed with the turbulence model. This two-dimensional computational fluid dynamics (CFD) analysis was performed with Ilorin, Kwara State, Nigeria wind data that was received from the Nigeria Meteorological Agency (NIMET). The modified blade with a wavelength of 0.09m and an amplitude of 0.004m is seen to have a better thrust than the unmodified blade. It produced a thrust of 118N for a tip-speed ratio (TSR) of 4.0 compared to 109N of the unmodified blade at the same TSR and that of the modified blade (1) which attains 107N. Also, its coefficient of performance is 5% and 6% higher than that of the straight and modified blades (1) respectively,suggest that an increase in the tubercle’s wavelength and amplitude increased the maximum thrust.
Understanding compressible flows over bluff bodies, such as circular cylinders, is critical for applications in aerospace engineering, space exploration, and astrophysics. However, the complexity of viscous and unsteady flows, compounded by compressibility effects, remains a challenge for experimental and computational methods. This study explores the compressible flow field of an impulsively started circular cylinder using Refined Potential Flow Theory (RPT), an analytical model that extends classical potential flow theory to include compressibility effects. The governing equations, boundary conditions, and refined stream function are developed to capture the density, velocity, and pressure fields in subsonic and transonic regimes. The results demonstrate that compressibility marginally increases vortex enstrophy at low Reynolds numbers, while its influence on wake flow stability diminishes at higher values. The study reveals that compressibility suppresses shear layer instability, reduces wake velocity deficits, and introduces smaller-scale structures that disrupt the inertial range of turbulence in the low subsonic regime. At higher Mach numbers (M∞≥0.6), local supersonic pockets and shock waves emerge, forming complex λ-shock systems and bow shocks. The predictions of the Strouhal number from RPT show marginal changes for 0.2≤M∞≤0.5, consistent with experimental and computational trends. Although RPT aligns with existing methods to capture key flow features, discrepancies in wake stability and recirculation zone dimensions highlight areas for further refinement. This research underscores the potential of RPT in developing optimization tools that complement experimental and numerical studies, offering valuable insights into compressible flow physics for engineering applications in high-altitude flight and space exploration.