22 September 2020 in Journal of Microelectromechanical Systems
MEMS-enabled multilayer composites, in which microfabrication is used to create micron-scale thickness layers within the volume of meso-scale thickness structures, can be exploited to create materials with highly anisotropic electromagnetic properties. Such materials have utility in both sensing and energy applications, including electrostatic and magnetic energy storage and conversion. A fabrication challenge in realizing these classes of materials lies in the size-scale disparity between the thickness of an individual layer and the desired thickness of the final anisotropic material. We demonstrate a fully additive sequential electrochemical deposition approach for such structures, which enables scalable composite volume while maintaining micron-scale individual layer thicknesses. Alternating metal and polymer layers, which exhibit very different electrical conductivities, are continuously electrodeposited in batch-scale. Individual layer thicknesses are controlled by deposition currents and times, while lateral extents are defined by lithographically defined molds. The fabrication process is illustrated using electrodeposited NiFe alloys and polypyrrole, and the anisotropy of electrical conductivity is assessed for potential use of these structures as magnetic cores for high frequency switching converters. Due to the relatively resistive polypyrrole layers, electrical anisotropy of lateral to vertical conductivity exceeding 10⁶ was achieved. This approach offers a solution-based, microfabrication compatible, and manufacturable route to functional composite materials that exhibit high electrical anisotropies. [2020-0256]
25 April 2022 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Metallic magnetic alloys are of interest as core materials in ultracompact or integrated inductors and transformers. However, when operated at high frequencies, such materials should comprise a multilayer stack of magnetic material laminations and electrically insulating interlayers to suppress eddy current loss. In order to achieve scalable and continuous fabrication of such a structure, sequential multilayer electrodeposition is an attractive approach. To achieve sequential electrodeposition, interlayer’s electrical conductivity should be sufficiently high to permit electrodeposition of subsequent layers, but sufficiently low to suppress eddy current loss. Polypyrrole, an electrodepositable polymer, was investigated as an interlayer material. Finite element modeling demonstrated a negligible difference in eddy current loss between NiFe/Polypyrrole and NiFe/vacuum multilayers. Experimental verification of the efficacy was demonstrated as well. Compared to a single layer NiFe inductor that has a comparable low frequency (10 kHz) inductance value, a laminated 10 layer NiFe core showed higher inductance retention (88% of the low frequency inductance for the laminated core vs. 21% for the single layer core), and lower AC resistance (1.68 ohm vs. 12.7 ohm) at 8 MHz; both of which are signs of suppressed eddy current. This scalable fabrication approach to high frequency inductors will facilitate power converter miniaturizations.
12 January 2023 in ChemRxiv
We report a synthesis method for highly monodisperse Cu-Pt alloy nanospheres. Small and large Cu-Pt particles with a Cu:Pt ratio of 1:1 can be obtained through colloidal synthesis at 300 °C. The fresh particles have a Pt-rich surface and a Cu-rich core and can be converted into an intermetallic phase after annealing at 800 °C under H2. First, we demonstrated the stability of fresh particles under redox conditions at 400 °C, as the Pt-rich surface prevents substantial oxidation of Cu. Then, a combination of in situ scanning transmission electron microscopy, in situ X-ray absorption spectroscopy, and CO oxidation measurements of the intermetallic CuPt phase before and after redox treatments at 800 °C showed promising activity and stability for CO oxidation. Full oxidation of Cu was prevented after exposure to O2 at 800 °C. The activity and structure of the particles was only slightly changed after exposure to O2 at 800 °C and were recovered after re-reduction at 800 °C. Additionally, the intermetallic CuPt phase showed enhanced catalytic properties compared to the fresh particles with a Pt-rich surface or pure Pt particles of the same size. Thus, the incorporation of Pt with Cu does not lead to a rapid deactivation and degradation of the material, as seen with other bimetallic systems. This work provides a synthesis route to control the design of Cu-Pt nanostructures and underlines the promising properties of these alloys (intermetallic and non-intermetallic) for heterogeneous catalysis.