James W. Borchert

James W. Borchert

Auto-generated profile, based on publicly available information

James W. Borchert

1st Institute of Physics Georg August University of Göttingen Friedrich‐Hund‐Platz 1 37077 Göttingen Germany

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 March 2019 in Nature Communications
Verified
Journal Article
Open access
PDF file
JBJames W. Borchert
James W. Borchert
BPBoyu Peng
Boyu Peng
FLFlorian Letzkus
Florian Letzkus
JBJoachim N. Burghartz
Joachim N. Burghartz
PCPaddy K. L. Chan
Paddy K. L. Chan
HKHagen Klauk
Hagen Klauk
The contact resistance in organic thin-film transistors (TFTs) is the limiting factor in the development of high-frequency organic TFTs. In devices fabricated in the inverted (bottom-gate) device architecture, staggered (top-contact) organic TFTs have usually shown or are predicted to show lower contact resistance than coplanar (bottom-contact) organic TFTs. However, through comparison of organic TFTs with different gate-dielectric thicknesses based on the small-molecule organic semiconductor 2,9-diphenyl-dinaphtho[2,3-b:2’,3’-f]thieno[3,2-b]thiophene, we show the potential for bottom-contact TFTs to have lower contact resistance than top-contact TFTs, provided the gate dielectric is sufficiently thin and an interface layer such as pentafluorobenzenethiol is used to treat the surface of the source and drain contacts. We demonstrate bottom-contact TFTs fabricated on flexible plastic substrates with record-low contact resistance (29 Ωcm), record subthreshold swing (62 mV/decade), and signal-propagation delays in 11-stage unipolar ring oscillators as short as 138 ns per stage, all at operating voltages of about 3 V.

22 May 2020 in Science Advances
Verified
Journal Article
Open access
PDF file
JBJames W. Borchert
James W. Borchert
UZUte Zschieschang
Ute Zschieschang
FLFlorian Letzkus
Florian Letzkus
MGMichele Giorgio
Michele Giorgio
RWR. Thomas Weitz
R. Thomas Weitz
HKHagen Klauk
Hagen Klauk
The primary driver for the development of organic thin-film transistors (TFTs) over the past few decades has been the prospect of electronics applications on unconventional substrates requiring low-temperature processing. A key requirement for many such applications is high-frequency switching or amplification at the low operating voltages provided by lithium-ion batteries (~3 V). To date, however, most organic-TFT technologies show limited dynamic performance unless high operating voltages are applied to mitigate high contact resistances and large parasitic capacitances. Here, we present flexible low-voltage organic TFTs with record static and dynamic performance, including contact resistance as small as 10 Ω·cm, on/off current ratios as large as 1010, subthreshold swing as small as 59 mV/decade, signal delays below 80 ns in inverters and ring oscillators, and transit frequencies as high as 21 MHz, all while using an inverted coplanar TFT structure that can be readily adapted to industry-standard lithographic techniques.

7 October 2021 in Advanced Materials
Verified
Journal Article
Open access
PDF file
JBJames W. Borchert
James W. Borchert
RWR. Thomas Weitz
R. Thomas Weitz
SLSabine Ludwigs
Sabine Ludwigs
HKHagen Klauk
Hagen Klauk
To take full advantage of recent and anticipated improvements in the performance of organic semiconductors employed in organic transistors, the high contact resistance arising at the interfaces between the organic semiconductor and the source and drain contacts must be reduced significantly. To date, only a small portion of the accumulated research on organic thin‐film transistors (TFTs) has reported channel‐width‐normalized contact resistances below 100 Ωcm, well above what is regularly demonstrated in transistors based on inorganic semiconductors. A closer look at these cases and the relevant literature strongly suggests that the most significant factor leading to the lowest contact resistances in organic TFTs so far has been the control of the thin‐film morphology of the organic semiconductor. By contrast, approaches aimed at increasing the charge‐carrier density and/or reducing the intrinsic Schottky barrier height have so far played a relatively minor role in achieving the lowest contact resistances. Herein, the possible explanations for these observations are explored, including the prevalence of Fermi‐level pinning and the difficulties in forming optimized interfaces with organic semiconductors. An overview of the research on these topics is provided, and potential device‐engineering solutions are discussed based on recent advancements in the theoretical and experimental work on both organic and inorganic semiconductors.

1 April 2022 in Science Advances
Verified
Journal Article
Open access
UZUte Zschieschang
Ute Zschieschang
UWUlrike Waizmann
Ulrike Waizmann
JWJürgen Weis
Jürgen Weis
JBJames W. Borchert
James W. Borchert
HKHagen Klauk
Hagen Klauk
Direct-write electron-beam lithography has been used to fabricate low-voltage p-channel and n-channel organic thin-film transistors with channel lengths as small as 200 nm and gate-to-contact overlaps as small as 100 nm on glass and on flexible transparent polymeric substrates. The p-channel transistors have on/off current ratios as large as 4 × 109and subthreshold swings as small as 70 mV/decade, and the n-channel transistors have on/off ratios up to 108and subthreshold swings as low as 80 mV/decade. These are the largest on/off current ratios reported to date for nanoscale organic transistors. Inverters based on two p-channel transistors with a channel length of 200 nm and gate-to-contact overlaps of 100 nm display characteristic switching-delay time constants between 80 and 40 ns at supply voltages between 1 and 2 V, corresponding to a supply voltage–normalized frequency of about 6 MHz/V. This is the highest voltage-normalized dynamic performance reported to date for organic transistors fabricated by maskless lithography.

4 April 2023 in Advanced Materials Technologies
Verified
Journal Article
Open access
UZUte Zschieschang
Ute Zschieschang
HKHagen Klauk
Hagen Klauk
JBJames W. Borchert
James W. Borchert
Organic thin‐film transistors are field‐effect transistors comprising a semiconductor in the form of a thin, typically polycrystalline layer of conjugated organic molecules. Since organic transistors can often be fabricated at temperatures no higher than about 100 °C, they are potentially useful for flexible, large‐area electronics applications. An important performance parameter of organic transistors is the transit frequency, which is the highest frequency at which the transistors can be operated. The transit frequency of organic transistors is determined in large part by the channel length and the parasitic gate‐to‐source and gate‐to‐drain overlap lengths. How small these dimensions can be made depends (at least in the case of transistors fabricated in the lateral device architecture) greatly on the resolution of the lithography method that is utilized for the patterning of the gate electrodes and the source and drain contacts. Patterning methods that have yielded organic transistors with lateral dimensions sufficiently small to provide transit frequencies above 10 MHz include photolithography, laser lithography, stencil lithography, and electron‐beam lithography. In this review, these four lithography methods and their roles in the fabrication of high‐frequency organic transistors, as well as their prospects for future improvements in the dynamic performance of organic transistors, will be illuminated.

6 February 2019 in Crystals
Verified
Journal Article
Open access
PDF file
MKMarkus Krammer
Markus Krammer
JBJames W. Borchert
James W. Borchert
APAndreas Petritz
Andreas Petritz
EKEsther Karner-Petritz
Esther Karner-Petritz
GSGerburg Schider
Gerburg Schider
KZKarin Zojer
Karin Zojer
The thin-film transistor (TFT) is a popular tool for determining the charge-carrier mobility in semiconductors, as the mobility (and other transistor parameters, such as the contact resistances) can be conveniently extracted from its measured current-voltage characteristics. However, the accuracy of the extracted parameters is quite limited, because their values depend on the extraction technique and on the validity of the underlying transistor model. We propose here a new approach for validating to what extent a chosen transistor model is able to predict correctly the transistor operation. In the two-step fitting approach we have developed, we analyze the measured current-voltage characteristics of a series of TFTs with different channel lengths. In the first step, the transistor parameters are extracted from each individual transistor by fitting the output and transfer characteristics to the transistor model. In the second step, we check whether the channel-length dependence of the extracted parameters is consistent with the underlying model. We present results obtained from organic TFTs fabricated in two different laboratories using two different device architectures, three different organic semiconductors and five different materials combinations for the source and drain contacts. For each set of TFTs, our approach reveals that the state-of-the-art transistor models fail to reproduce correctly the channel-length-dependence of the transistor parameters. Our approach suggests that conventional transistor models require improvements in terms of the charge-carrier-density dependence of the mobility and/or in terms of the consideration of uncompensated charges in the carrier-accumulation channel.