Jae-Sang Kim

Jae-Sang Kim

Auto-generated profile, based on publicly available information

Jae-Sang Kim

Department of Electrical Engineering, Korea Advanced Institute of Science and Technology, Daejeon, South Korea

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 June 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KKKeon-Woo Kim
Keon-Woo Kim
YJYeonho Jeong
Yeonho Jeong
JKJae-Sang Kim
Jae-Sang Kim
GMGun-Woo Moon
Gun-Woo Moon
A new structure of the transformer and its winding layout are proposed to reduce the common-mode (CM) noise generated from the planar transformer (PT). In the proposed converter, two half-bridge LLC resonant converters are connected in parallel on the primary side, and secondary side of them are connected in series. The proposed converter can be utilized for the medium-to-high power applications due to the full-bridge structure of the primary side. For each transformer, one of the terminals is connected to the static-point, which has zero dv/dt characteristic. Thus, the primary side layer can have the same dv/dt characteristics with the secondary side layer. By adjacently locating the primary and secondary layers which have the same dv/dt characteristic, the CM current and noise generated from PT can be significantly reduced. Therefore, the proposed converter can achieve a high power density by reducing the size of EMI filter.

14 February 2022 in IEEE Transactions on Aerospace and Electronic Systems
Verified
Journal Article
Closed access
SHSang-Hyeon Ha
Sang-Hyeon Ha
JLJae-In Lee
Jae-In Lee
HYHyunki Yoon
Hyunki Yoon
TPTae-Ryong Park
Tae-Ryong Park
JBJaeil Baek
Jaeil Baek
GMGun-Woo Moon
Gun-Woo Moon
This article presents a frequency-variable resonant self-heating technique for improving the heating speed of lithium-ion batteries at very low temperatures. In contrast to the conventional heating method with a fixed current and frequency, the proposed technique can increase the battery heating current by determining the minimum impedance of the lithium-ion batteries. Then, through a variable charging/discharging frequency operation, this technique can increase the heating speed without inducing a temperature plateau because of impedance reduction. A lithium-ion battery with improved self-heating performance at low temperatures was developed and used to verify the proposed self-heating technique. A simulation model and self-heating device (dc/dc converters) were also designed and tested at –30-°C ambient temperature. The proposed frequency-variable resonant self-heating technique achieved a heating speed four times faster (from 2784 s to 717 s) than the conventional self-heating technique. Thus, lithium-ion batteries can be used at cryogenic temperatures (–30 °C) by quickly raising the battery temperature with this technique.

21 September 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KKKeon-Woo Kim
Keon-Woo Kim
YJYeonho Jeong
Yeonho Jeong
JKJae-Sang Kim
Jae-Sang Kim
GMGun-Woo Moon
Gun-Woo Moon
This article proposes a low common-mode (CM) noise full-bridge LLC resonant converter with two balanced resonant tanks. In the proposed converter, each resonant inductor and capacitor is divided into two components with the same value. The CM current flowing through parasitic capacitors of the transformer is reduced due to the balanced resonant tank. Moreover, the CM noise can be significantly reduced by adjacently locating the primary and secondary layers with the same dv/dt characteristic. Therefore, the proposed converter decreases the CM noise generated from the planar transformer (PT) by the balanced resonant tank and proposed layer arrangement of PT and achieves a high power density with a decreased size of the electromagnetic interference filter. The validity of the proposed converter is verified by a 1.5-kW prototype with 400-V input and 270-420-V output.

10 October 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JKJae-Sang Kim
Jae-Sang Kim
TKTaewoo Kim
Taewoo Kim
JBJuhyun Bae
Juhyun Bae
JHJung-Kyu Han
Jung-Kyu Han
GMGun-Woo Moon
Gun-Woo Moon
Server power supply has to maintain output power even under abnormal input voltage conditions for stable operation of the server. Input-voltage-based current reference control has been widely used for power factor correction converter in server power supply because it can instantly generate a current reference and maintain a stable output. However, because harmonics and noise in the input voltage directly influence the current reference, the input current total harmonic distortion (THD) increases. On the other hand, phase-locked loop (PLL) based control can achieve lower current THD due to its excellent noise and harmonic filtering capabilities, but it cannot respond to sudden changes in the input voltage. In this letter, a hybrid current reference control method is proposed to achieve stable operation of the server power supply. The proposed method ensures continuous operation under abnormal input voltages by utilizing input-voltage-based control. Therefore, in normal input condition, the PLL bandwidth design can be alleviated to achieve a lower current THD. To determine the effectiveness of the proposed control method, steady-state operation and abnormal input condition operation were confirmed through a 47–64 Hz/90–264 V rms 3-kW prototype converter.

15 June 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JBJuhyun Bae
Juhyun Bae
JKJae-Sang Kim
Jae-Sang Kim
MLMinsu Lee
Minsu Lee
JHJung-Kyu Han
Jung-Kyu Han
GMGun-Woo Moon
Gun-Woo Moon
A conventional asymmetrical half-bridge (AHB) converter is one of the widely used topologies in low to medium power applications. However, when it is designed in a wide input voltage range, it operates with a low duty ratio at nominal input voltage. In addition, it has disadvantages, such as a dc offset of magnetizing current, an unbalanced average current of the diode, and a nonlinear voltage gain due to asymmetrical operation. To solve these disadvantages, an AHB converter with linear voltage gain is proposed. The proposed converter has a structure in which a capacitor is added as a voltage source to obtain a symmetrical operation by extending the commutation period. Therefore, it has a narrow range of operating duty ratio and a zero dc offset of magnetizing current. Due to the zero dc offset of magnetizing current, it has a small size transformer and improved zero-voltage switching conditions of the primary-side switches. In addition, it has a low primary rms current and a balanced average current of the diode. Consequently, the proposed converter has high efficiency under the entire load conditions. A 300–400 V input and 48 V/400 W output prototype is tested to verify the feasibility of the proposed converter.

19 October 2023 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
DCDongmin Choi
Dongmin Choi
MLMinsu Lee
Minsu Lee
TKTaewoo Kim
Taewoo Kim
JKJae-Sang Kim
Jae-Sang Kim
GMGun-Woo Moon
Gun-Woo Moon
This article proposes a novel offset current modulation technique, which can add a new degree of freedom to the dual active bridge dc–dc converter. The concept of the proposed technique is to inject offset currents into the primary- and secondary-sides of the transformer. If the same offset currents are injected into both sides, dc bias does not occur in the magnetizing current of the transformer. Therefore, the offset current can be used as a new control variable without any adverse effects. When the proposed technique is applied to single phase shift (SPS) modulation, zero voltage switching (ZVS) characteristics can be further improved by realizing the ZVS of two more switches, leading to higher efficiency. Furthermore, the proposed control system can be configured with simple modification of the conventional control system. The optimal SPS modulation with the proposed technique is derived through theoretical loss optimization considering a tradeoff between conduction loss and switching loss. The feasibility of the proposed technique is verified using a 3.3 kW prototype with a 400 V input and 280–420 V output conditions.