5 February 2015 in IEEE Transactions on Electron Devices
In this paper, a short-gate tunneling-field-effect-transistor (SG-TFET) structure has been investigated for the dielectrically modulated biosensing applications in comparison with a full-gate tunneling-field-effect-transistor structure of similar dimensions. This paper explores the underlying physics of these architectures and estimates their comparative sensing performance. The sensing performance has been evaluated for both the charged and charge-neutral biomolecules using extensive device-level simulation, and the effects of the biomolecule dielectric constant and charge density are also studied. In SG-TFET architecture, the reduction of the gate length enhances its drain control over the band-to-band tunneling process and this has been exploited for the detection, resulting to superior drain current sensitivity for biomolecule conjugation. The gate and drain biasing conditions show dominant impact on the sensitivity enhancement in the short-gate biosensors. Therefore, the gate and drain bias are identified as the effective design parameters for the efficiency optimization.
6 May 2016 in IEEE Transactions on Electron Devices
Dielectrically modulated tunnel FET (DMTFET)-based biosensors show higher sensitivity but lower subthreshold current compared with their dielectrically modulated FET counterpart. In this context, the effect of use of silicon-germanium (SiGe) source and n + -pocket-doped channel is investigated with the help of extensive device-level simulations. This paper explores the underlying physics of germanium composition variation in the source region, and doping concentration variation in n + -pocket region, from the perspective of biomolecule conjugation. The effects of source bandgap and tunneling length over the band-to-band tunneling component have been analyzed, and, subsequently, the sensing performance of DMTFETs has been estimated. The results show that SiGe-source DMTFET has significant superiority over n + -pocket DMTFET for attaining higher subthreshold current level while retaining acceptable sensitivity. Such sensitivity-current optimization has been studied for different gate and drain biases, and the suitable biasing range of operation has been indicated. In addition, the relative efficiency of SiGe source and n + -pocket-doped channel has been studied under different biomolecule sample specifications. Finally, the influence of trap-assisted tunneling on DMTFET sensing performance has been analyzed, and the comparative role of SiGe source and n + pocket has also been indicated in this context.
25 October 2017 in IEEE Transactions on Device and Materials Reliability
This paper concerns the selectivity tuning of graphene oxide based gas sensor devices, where the role of oxygen functional groups like, carboxyl, carbonyl, hydroxyl (sp2), epoxy, and hydroxyl (sp3) were investigated for physisorption of NO2, NH3, CO, and H2O using first principle calculation (density functional theory) incorporating Atomistix Toolkit (v2015.1). Among the five functional groups under consideration, carboxyl, carbonyl, and hydroxyl (sp2) were considered at the edges on the basal plane, while epoxy and hydroxyl (sp3) groups were considered in the plane perpendicular to that. For all the species, the optimum positions for adsorption, adsorption energy and charge transfer efficiency were investigated for the above two planes. It was found that edge carboxyl group is the most favorable in terms of adsorption energy and charge transfer efficiency targeting NH3, CO, and H2O. On the contrary, for NO2, hydroxyl functionalization was found to be the most efficient one.
1 January 2015 in IEEE Transactions on Nanotechnology
In this paper, the crosstalk effects in both small and large diameter multiwalled carbon nanotube bundle interconnects (MWCNTs) for the future nanoscale integrated circuits are studied with the help of ABCD parameter matrix approach for global levels of interconnects at 22- and 14-nm technology nodes. Here, isolated MWCNTs are modeled using an equivalent single conductor transmission line. The simulation results show that the results are at par with the result of SPICE model. It is observed that performance wise, the large diameter MWCNT bundles are better than both small diameter MWCNT bundles and copper wire for both repeated and unrepeated interconnects. The same trend is observed with the number of inserted repeaters. For repeated wires, the optimized placement of repeaters offsets the delay advantage numbers of MWCNT bundles over copper wire. Technology scaling adversely impacts the delay advantage numbers of small diameter MWCNT bundles. As far as the worst-case crosstalk noise peak voltage is concerned, the large diameter MWCNT bundles also outperform both small diameter MWCNT bundles and copper wire for longer interconnects. However, for shorter interconnects, copper wire and small diameter bundles outclass the large diameter bundles due to their relatively larger time constant. We have compared our crosstalk analysis results with the earlier work to justify the validity of our proposed model and observed that the results with our model are in well conformity with the existing work. It is seen that even the tall Cu vias are not going to significantly affect the performance of MWCNT bundle interconnects. Twice the minimum width global level interconnects are the optimal choice to achieve the maximum delay advantage using MWCNT bundle interconnects in comparison with Cu-based interconnects. Finally, our analysis shows that from the performance and signal integrity perspective, the large diameter MWCNT bundles are a suitable alternative to both small diameter MWCNT bundles and copper interconnects for future integrated circuit technology generations.
25 April 2011 in IEEE Transactions on Nanotechnology
This paper analyses the crosstalk effects in carbon nanotube (CNT) interconnect, and its impact on the gate oxide reliability. Using the existing models of CNT, circuit parameters for the single-wall CNT-bundle and multiwall CNT interconnects are calculated and the equivalent circuit has been developed to perform the crosstalk analysis. The crosstalk-induced overshoot/undershoots have been estimated and the impact of the overshoot/undershoots on the gate oxide reliability in terms of failure-in-time rate is calculated. A similar analysis is performed for Cu-based interconnects and comparisons are made with the results obtained for CNT-based interconnect. It has been found that the CNT-based interconnect is more suitable in VLSI circuits as far as the gate oxide reliability is concerned.
1 February 2014 in Computers and Electrical Engineering