Adam Ginsburg

Adam Ginsburg

Auto-generated profile, based on publicly available information

Adam Ginsburg

Department of Chemistry, Center for Nanotechnology & Advanced Materials, Bar Ilan University, Ramat Gan 52900, Israel.

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2015 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Open access
MPMichele Pavan
Michele Pavan
SRSven Rühle
Sven Rühle
AGAdam Ginsburg
Adam Ginsburg
DKDavid A. Keller
David A. Keller
HBHannah-Noa Barad
Hannah-Noa Barad
Elvira FortunatoElvira Fortunato
Elvira Fortunato
Here we present for the first time a TiO2/Cu2O all-oxide heterojunction solar cell entirely produced by spray pyrolysis onto fluorine doped tin oxide (FTO) covered glass substrates, using silver as a back contact. A combinatorial approach was chosen to investigate the impact of the TiO2 window layer and the Cu2O light absorber thicknesses. We observe an open circuit voltage up to 350mV and a short circuit current density which is strongly dependent of the Cu2O thickness, reaching a maximum of ~0.4mA/cm2. Optical investigation reveals that a thickness of 300nm spray pyrolysis deposited Cu2O is sufficient to absorb most photons with an energy above the symmetry allowed optical transition of 2.5eV, indicating that the low current densities are caused by strong recombination in the absorber that consists of small Cu2O grains

12 January 2016 in Nanoscale
Verified
Journal Article
Closed access
PDF file
LGLaxman Gouda
Laxman Gouda
Ronen GottesmanRonen Gottesman
Ronen Gottesman
STShay Tirosh
Shay Tirosh
EHEynav Haltzi
Eynav Haltzi
JHJiangang Hu
Jiangang Hu
AZArie Zaban
Arie Zaban
Hybrid methyl-ammonium lead trihalide perovskites are promising low-cost materials for use in solar cells and other optoelectronic applications. With a certified photovoltaic conversion efficiency record of 20.1%, scale-up for commercial purposes is already underway. However, preparation of large-area perovskite films remains a challenge, and films of perovskites on large electrodes suffer from non-uniform performance. Thus, production and characterization of the lateral uniformity of large-area films is a crucial step towards scale-up of devices. In this paper, we present a reproducible method for improving the lateral uniformity and performance of large-area perovskite solar cells (32 cm2). The method is based on methyl-ammonium iodide (MAI) vapor treatment as a new step in the sequential deposition of perovskite films. Following the MAI vapor treatment, we used high throughput techniques to map the photovoltaic performance throughout the large-area device. The lateral uniformity and performance of all photovoltaic parameters (Voc, Jsc, Fill Factor, Photo-conversion efficiency) increased, with an overall improved photo-conversion efficiency of ∼100% following a vapor treatment at 140 °C. Based on XRD and photoluminescence measurements, We propose that the MAI treatment promotes a “healing effect” to the perovskite film which increases the lateral uniformity across the large-area solar cell. Thus, the straightforward MAI vapor treatment is highly beneficial for large scale commercialization of perovskite solar cells, regardless of the specific deposition method.

4 January 2016 in Advanced Materials Interfaces
Verified
Journal Article
Open access
PDF file
KMKoushik Majhi
Koushik Majhi
LBLuca Bertoluzzi
Luca Bertoluzzi
KRKevin James Rietwyk
Kevin James Rietwyk
AGAdam Ginsburg
Adam Ginsburg
DKDavid A. Keller
David A. Keller
AZArie Zaban
Arie Zaban
In article number 1500405, A. Zaban and co-workers show the effectiveness of a MoO3 buffer/hole-contact layer for improving the performance of Co3O4|TiO2 all-oxide hetero-junction solar cells. The performance is found to be restricted by a poor interface with Au back contacts arising from surface recombination at the Au|Co3O4 interface. This detrimental effect can be overcome via the introduction of a thin layer of MoO3 between Au and Co3O4 layers.