1 January 2015 in Solar Energy Materials and Solar Cells
Here we present for the first time a TiO2/Cu2O all-oxide heterojunction solar cell entirely produced by spray pyrolysis onto fluorine doped tin oxide (FTO) covered glass substrates, using silver as a back contact. A combinatorial approach was chosen to investigate the impact of the TiO2 window layer and the Cu2O light absorber thicknesses. We observe an open circuit voltage up to 350mV and a short circuit current density which is strongly dependent of the Cu2O thickness, reaching a maximum of ~0.4mA/cm2. Optical investigation reveals that a thickness of 300nm spray pyrolysis deposited Cu2O is sufficient to absorb most photons with an energy above the symmetry allowed optical transition of 2.5eV, indicating that the low current densities are caused by strong recombination in the absorber that consists of small Cu2O grains
1 April 2016 in Solar Energy Materials and Solar Cells
13 August 2014 in Advanced Energy Materials
15 October 2015 in Nanotechnology
Advances in high-throughput materials fabrication and characterization techniques have resulted in faster rates of data collection and rapidly growing volumes of experimental data. To convert this mass of information into actionable knowledge of material process-structure-property relationships requires high-throughput data analysis techniques. This work explores the use of the Graph-based endmember extraction and labeling (GRENDEL) algorithm as a high-throughput method for analyzing structural data from combinatorial libraries, specifically, to determine phase diagrams and constituent phases from both x-ray diffraction and Raman spectral data. The GRENDEL algorithm utilizes a set of physical constraints to optimize results and provides a framework by which additional physics-based constraints can be easily incorporated. GRENDEL also permits the integration of database data as shown by the use of critically evaluated data from the Inorganic Crystal Structure Database in the x-ray diffraction data analysis. Also the Sunburst radial tree map is demonstrated as a tool to visualize material structure-property relationships found through graph based analysis.
11 November 2015 in The Journal of Physical Chemistry Letters
The high open-circuit potential (Voc) achieved by perovskite solar cells (PSCs) is one of the keys to their success. The Voc analysis is essential to understand their working mechanisms. A large number of CH3NH3PbI3–xClx PSCs were fabricated on single large-area substrates and their Voc dependencies on illumination intensity, I0, were measured showing three distinctive regions. Similar results obtained in Al2O3 based PSCs relate the effect to the compact TiO2 rather than the mesoporous oxide. We propose that two working mechanisms control the Voc in PSCs. The rise of Voc at low I0 is determined by the employed semiconductor n-type contact (TiO2 or MgO coated TiO2). In contrast, at I0 close to AM1.5G, the employed oxide does not affect the achieved voltage. Thus, a change of regime from an oxide-dominated EFn (as in the dye sensitized solar cells) to an EFn, directly determined by the CH3NH3PbI3–xClx absorber is suggested.
30 October 2015 in Advanced Materials Interfaces
A TiO2|Co3O4|MoO3 all‐oxide solar cell produced by spray pyrolysis and pulsed laser deposition (PLD) onto a fluorine‐doped tin‐oxide (FTO) glass substrate with gold (Au) back contacts is demonstrated for the first time. A combinatorial approach is implemented to study the effect of molybdenum oxide (MoO3) as a recombination contact and the influence of the cobalt oxide (Co3O4) light‐absorber thickness on the performance of the solar cells. An increase of more than 200 mV in the open circuit voltage (Voc) is observed with a concurrent enhancement in terms of short‐circuit current (Jsc) and maximum power in comparison with TiO2|Co3O4 devices without the MoO3 layer. To understand the mechanism, full drift diffusion simulations are performed. The higher performance is attributed to elimination of a recombination process at the absorber/metal back‐contact interface and surface passivation by the MoO3 layer.