Yuanhang Qu

Yuanhang Qu

Auto-generated profile, based on publicly available information

Yuanhang Qu

Institute of Technological Sciences, Wuhan University, Wuhan, China

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2023 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
TLTiancheng Luo
Tiancheng Luo
QXQinwen Xu
Qinwen Xu
ZWZhiwei Wen
Zhiwei Wen
YQYuanhang Qu
Yuanhang Qu
JZJie Zhou
Jie Zhou
CSChengliang Sun
Chengliang Sun
Spurious modes (SMs) suppression and electromechanical coupling coefficient ( ${k}_{t}^{{2}}$ ) improvement in Lamb wave resonators (LWRs) have always been the research hotspot. In this work, a 2.5 GHz spurious-free S1 mode AlN/ScAlN-based LWR with trapezoidal electrodes is proposed. The AlN/Sc0.096AlN composite film is prepared by Physical Vapor Deposition (PVD) to improve the ${k}_{t}^{{2}}$ without numerous abnormal grains. Measured results show that the SMs are effectively suppressed over a wide frequency range (1.5–3.5 GHz). Relying on the using of AlN/Sc0.096AlN composite film and the elimination of SMs, the ${k}_{t}^{{2}}$ of the S1 mode has been increased to more than twice and the ${f}\times {Q}\times {k}_{t}^{{2}}$ of the device can reach up to ${1}.{08}\times {10}^{{11}}$ Hz.

12 September 2023 in Electronics
Verified
Journal Article
Open access
PDF file
MWMin Wei
Min Wei
YLYan Liu
Yan Liu
YQYuanhang Qu
Yuanhang Qu
XGXiyu Gu
Xiyu Gu
YWYilin Wang
Yilin Wang
CSChengliang Sun
Chengliang Sun
Temperature monitoring in extreme environments presents new challenges for MEMS sensors. Since aluminum nitride (AlN)/scandium aluminum nitride (ScAlN)-based surface acoustic wave (SAW) devices have a high Q-value, good temperature drift characteristics, and the ability to be compatible with CMOS, they have become some of the preferred devices for wireless passive temperature measurement. This paper presents the development of AlN/ScAlN SAW-based temperature sensors. Three methods were used to characterize the temperature characteristics of a thin-film SAW resonator, including direct measurement by GSG probe station, and indirect measurement by oscillation circuit and antenna. The temperature characteristics of the three methods in the range of 30–100 °C were studied. The experimental results show that the sensitivities obtained with the three schemes were −28.9 ppm/K, −33.6 ppm/K, and −29.3 ppm/K. The temperature sensor using the direct measurement method had the best linearity, with a value of 0.0019%, and highest accuracy at ±0.70 °C. Although there were differences in performance, the characteristics of the three SAW temperature sensors make them suitable for sensing in various complex environments.

13 June 2023 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
XGXiyu Gu
Xiyu Gu
YLYan Liu
Yan Liu
YXYing Xie
Ying Xie
ZWZhiwei Wen
Zhiwei Wen
YQYuanhang Qu
Yuanhang Qu
CSChengliang Sun
Chengliang Sun
How to improve the quality factor (Q) of transversely excited bulk wave resonators (XBARs) has become a key technical problem in the RF field. In this study, a XBAR with 2 μm gap-width reflector based on LiNbO 3 was fabricated to attain Qp value of 1211, exceeding the measurement in typical XABR ( Qp = 372). Simulation results indicate that the capacity of reflector gap width to inhibit the propagation of longitudinal wave energy increases first and then decreases as gap width increases from 0.5 μm to 8 μm The measurement results obtained from XBAR with 2 μm gap-width reflectors and XBAR with 4 μm gap-width reflectors ( Qp = 802) demonstrate excellent consistency with the simulation results. This study presents the XBAR with largest Qp × K 2 eff (237.4) currently, which highlights the significant potential of utilizing smaller gap-width reflectors in XBARs to construct filters with large bandwidth and high frequency.

27 February 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
LNLaixia Nian
Laixia Nian
YQYuanhang Qu
Yuanhang Qu
XGXiyu Gu
Xiyu Gu
TLTiancheng Luo
Tiancheng Luo
YXYing Xie
Ying Xie
CSChengliang Sun
Chengliang Sun
Piezoelectric aluminum nitride (AlN) thin film, as a commonly used material for high-frequency acoustic resonators, has been a research hotspot in the RF field. Doping Sc elements in AlN is one of most effective methods to improve the piezoelectricity of the material. In this work, the first principal calculation and Mori–Tanaka model are used to obtain the piezoelectric constants of AlN, ScAlN, and AlN/ScAlN composites. Then, five types of AlN/ScAlN thin films are prepared on 8 inch silicon substrates. The crystal quality, roughness, and stress distribution are measured to characterize the film quality. The results show that composite film can effectively solve the problem of abnormal grains and reduce the roughness. Finally, a lamb wave resonator with an AlN/Sc0.2Al0.8N composite working at 2.33 GHz is fabricated. The effective electromechanical coupling coefficient Keff2 is calculated to be 6.19%, which has the potential to design high-frequency broadband filters.

3 February 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
XHXiaoming Huang
Xiaoming Huang
XGXiyu Gu
Xiyu Gu
CYChaoxiang Yang
Chaoxiang Yang
JDJiaqi Ding
Jiaqi Ding
XCXiang Chen
Xiang Chen
Shishang GuoShishang Guo
Shishang Guo
How to improve the sensitivity of Micro-electromechanical systems (MEMS) piezoelectric accelerometers has become a key technical problem in consumer electronics. In this paper, a multigrooved cantilever-type piezoelectric accelerometer based on composite film is manufactured to obtain high sensitivity of 4.62 mV/g, excessing typical accelerometer (3.36 mV/g). The theoretical model and finite element model are established to analyze the relationship between cantilever stiffness, stress distribution and sensitivity. The proposed accelerometers are fabricated by MEMS processes to form Mo/AlN/ScAlN/Mo piezoelectric stacks as the sensing layer. The experimental results show that the sensitivity, linearity, minimum detectable signal (MDS), and resonant frequency of the proposed piezoelectric accelerometer with multiple grooves are 4.62 mV/g, 0.99964, 0.02 g, and 15320 Hz, respectively. This new structure can provide inspiration for the design of high-sensitivity and high-linear MEMS piezoelectric accelerometers.

13 February 2023 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
YQYuanhang Qu
Yuanhang Qu
XGXiyu Gu
Xiyu Gu
YZYang Zou
Yang Zou
ZWZhiwei Wen
Zhiwei Wen
YCYao Cai
Yao Cai
CSChengliang Sun
Chengliang Sun
In order to reduce the lateral acoustic energy loss of thin film bulk acoustic resonators (FBARs), the trench structure for FBAR is generally designed to block the leakage of acoustic wave and help improving the $Q$ -factor. One method the designers often used is etching the piezoelectric material around the active area of the FBAR to form the air-wall structure as a perfect reflection boundary condition. In this paper, the FBAR with trench structure is fabricated. The multilayer films in the FBAR with trench structure are easily warped due to excessive compressive stress. The numerical analysis and finite element simulation are used to verify the effects of different stresses on the devices. In order to avoid the degradation of FBAR performance caused by film warpage, the FBAR with anchor columns is proposed. The anchor columns are located on both sides of the FBAR, and they are designed to reduce film bending and the compressive stress of active area of the resonator. The measured results show that the Qs and Qp of the FBAR with anchor columns are increased by 55.8% and 21.1%, respectively, and $k_{eff}{}^{2}$ improved from 5.6% to 6.7% compared with the FBAR without the anchor columns. 2022-0179