17 June 2025 in International Journal of Engine Research
This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. With the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.
1 October 2025 in Energy Conversion and Management
19 August 2026 in SSRN Electronic Journal
Methanol (MeOH) is considered as a promising alternative fuel for propulsion and power systems owing to its high octane number and oxygenated molecular structure. However, its high latent heat of vaporization and volatility strongly influence spray evaporation and mixture formation, especially under cold start conditions. In this study, MeOH sprays in a gasoline direct injection (GDI) configuration were investigated in a constant volume spray chamber under a range of simulated engine-relevant conditions. Macroscopic and microscopic imaging diagnostics were applied to characterize liquid- and vapor-phase spray development, plume interaction, liquid volume fraction distribution, and droplet characteristics.The results show that injection pressure primarily controls initial spray momentum and penetration, whereas ambient pressure and temperature dominate evaporation and phase distribution. Increasing injection pressure accelerated liquid penetration and enlarged early-stage spray volume, while reducing liquid-phase residence time at fixed downstream locations. Under elevated ambient pressure and temperature, the liquid phase was rapidly suppressed and evaporated at short penetration length, while vapor-phase fuel continued to propagate beyond the liquid boundary, resulting in the largest separation between the liquid- and vapor-phase penetration. On the other hand, under simulated intake stroke conditions with low ambient pressure, MeOH flash boiling produced rapid axial penetration followed by plume collapsing and merging. This regime reduced the downstream spray width despite enhanced penetration and showed the largest deviation between plume direction angle and the nozzle drill angle among all tested conditions. Three-dimensional (3D) liquid volume fraction (LVF) data further indicated that these features originated from plume-to-plume interaction, collapsing, and redistribution of liquid volume within the spray. Microscopic imaging showed larger cone angles and smaller droplet size under low-pressure conditions, whereas high ambient pressure produced a denser near-nozzle liquid core and smaller plume cone angles.
25 October 2025 in International Journal of Engine Research
This study focused on conducting three-dimensional (3D) computational fluid dynamics (CFD) simulations to evaluate the impact of wall-guided spark plug ignition assistance on gasoline compression ignition (GCI) combustion performance during cold operations. The numerical simulations were performed on a 6-cylinder, 15 L heavy-duty diesel engine operating at a compression ratio (CR) of 16.5 using RON92 E0 gasoline. Spark assistance was simulated by incorporating an ignition model with the necessary spark energy to ensure stable combustion during cold operations. Initially, closed-cycle 3D CFD combustion simulations, based on a design of experiments (DoE) campaign, were employed to investigate a lean spark-assisted CI strategy during the cold-to-warm transition. A numerical optimization approach, based on a Response Surface Model (RSM), was adopted to optimize injector spray patterns, fuel injection strategies, and in-cylinder swirl motion to achieve the best performance of wall-guided spark assistance combustion. The optimized injector spray pattern, fuel injection strategy, and swirl ratio were predicted to provide 12 percentage points increase in combustion efficiency over the baseline, while meeting constraints for maximum pressure rise rate (MPRR) and NO x emissions (MPRR < 5 bar/CAD and NO x < 2 g/kWh). Building on the aforementioned optimal design, an open-cycle 3D CFD analysis was subsequently carried out to simulate engine starts at various cold ambient temperatures using a stoichiometric, spark-initiated flame propagation strategy. The results showed that with the optimized design, reasonable GCI combustion during engine starts was achieved at cold ambient temperature of 300 K. Notably, as the ambient temperature decreases from 300 to 243 K, the emergence of a noticeable fuel film was observed, presenting an undesirable potential for increased engine-out unburned hydrocarbon and smoke emissions. Considering the specific emission requirements at lower ambient temperatures, further investigations are warranted to assess the significance of the observed fuel film in relation to these criteria.