Anqi Zhang

Anqi Zhang

Auto-generated profile, based on publicly available information

Anqi Zhang

Aramco Americas, Aramco Research Center - Detroit, Novi, MI, USA

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 January 2025 in Fuel
Verified
Journal Article
Closed access
LZLe Zhao
Le Zhao
AZAnqi Zhang
Anqi Zhang
RSRafael Lago Sari
Rafael Lago Sari
SPSriram S Popuri
Sriram S Popuri
NBNick Bowen
Nick Bowen
GMGriffin Matuszak
Griffin Matuszak

19 May 2021 in Journal of Energy Resources Technology
Verified
Journal Article
Open access
PDF file
BSBrandon A. Sforzo
Brandon A. Sforzo
ATAniket Tekawade
Aniket Tekawade
AKAlan L. Kastengren
Alan L. Kastengren
KFKamel Fezzaa
Kamel Fezzaa
JIJan Ilavsky
Jan Ilavsky
RLRobert Levy
Robert Levy
The effects of fuel blend properties on spray and injector performance has been investigated in a side-mount injector for gasoline direct injection (GDI) using two certification fuel blends: Euro 5 and Euro 6. Several X-ray diagnostic techniques were conducted to characterize the injector and spray morphology. Detailed internal geometry of the GDI injector was resolved to 1.8 μm, through the use of hard X-ray tomography. The geometry characterization of this six-hole GDI, side mount injector, quantifies relevant hole and counterbore dimensions and reveals the intricate details within the flow passages, including surface roughness and micron-sized features. Internal valve motion was measured with a temporal resolution of 20 μs and a spatial resolution of 2.0 μs, for three injection pressures and several injector energizing strategies. The needle motion for both fuels exhibits similar lift profiles for common energizing commands. A combination of X-ray radiography and ultra-small-angle X-ray scattering (USAXS) was used to characterize the fuel mass distribution and the droplet sizing, respectively. Tomographic spray radiography revealed the near-nozzle distribution of fuel mass for each of the fuels and the asymmetry produced by the angled nozzles. Under evaporative conditions, the two fuels show minor differences in peak fuel mass distribution during steady injection, though both exhibit fluctuations in injection during the early, transient phase. USAXS measurements of the path-specific surface area of the spray indicated lower peak values for the more evaporative conditions in the near nozzle region.

24 October 2025 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
RMRafael Menaca
Rafael Menaca
XLXinlei Liu
Xinlei Liu
BMBalaji Mohan
Balaji Mohan
AZAnqi Zhang
Anqi Zhang
MSMickael Silva
Mickael Silva
HIHong G. Im
Hong G. Im

27 June 2024 in Fuel
Verified
Journal Article
Closed access
DBDiego Bestel
Diego Bestel
JKJoohan Kim
Joohan Kim
LZLe Zhao
Le Zhao
AZAnqi Zhang
Anqi Zhang
JPJi-Woong Park
Ji-Woong Park
RTRoberto Torelli
Roberto Torelli

26 November 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
LZle zhao
le zhao
YZYu Zhang
Yu Zhang
YPYuanjiang Pei
Yuanjiang Pei
AZAnqi Zhang
Anqi Zhang
MAMuhsin Ameen
Muhsin Ameen
A closed-cycle, three-dimensional (3D) computational fluid dynamics (CFD) analysis campaign was conducted to evaluate the performance of using spark plugs to assist gasoline compression ignition (GCI) combustion during cold idle operations. A conventional spark plug using single-sided J-strap design was put at a location on the cylinder head to facilitate spray-guided spark assistance. Ignition was modeled with an L-type energy distribution to depict the breakdown and the arc-to-glow phases during the energy discharge process. Several key design parameters were investigated, including injector clocking, number of nozzle holes, spray inclusion angle, number of fuel injections, fuel split ratio, and fuel injection timings. The study emphasized the region around the spark gap, focusing on flame kernel formation and development and local equivalence ratio distribution. Flame kernel development and the ignition process were found to correlate strongly with the fuel stratification and the flow velocity near the spark gap. The analysis results showed that the flame kernel development followed the direction of the local flow field. In addition, the local fuel stratification notably influenced early-stage flame kernel development due to varying injection spray patterns and the fuel injection strategies. Among these design parameters, the number of nozzle holes and fuel injection timing had the most significant effects on the engine combustion performance.

17 June 2025 in International Journal of Engine Research
Verified
Journal Article
Closed access
HLHao-Pin Lien
Hao-Pin Lien
DBDiego Bestel
Diego Bestel
LZLe Zhao
Le Zhao
AZAnqi Zhang
Anqi Zhang
JPJi-Woong Park
Ji-Woong Park
RTRoberto Torelli
Roberto Torelli
This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. With the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.