Mateusz Bednarski

Mateusz Bednarski

Auto-generated profile, based on publicly available information

Mateusz Bednarski

Combustion Engines Department, Institute of Vehicles, Warsaw University of Technology

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 January 2019 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
JLJakub Lasocki
Jakub Lasocki
MBM Bednarski
M Bednarski
MSMieczysław Sikora
Mieczysław Sikora
Ammonia is regarded as an attractive alternative fuel for combustion engines with a great potential to replace currently used petroleum-based energy carriers. Its direct combustion does not result in emission of carbon dioxide and it can be produced from renewable sources. The energy density of ammonia is reasonable, it is relatively easy to store and has well established infrastructure for production, storage, handling and distribution. However, ammonia is corrosive to some materials, difficult to ignite due to high octane number and high autoignition temperature, and has low heating value. Therefore theoretical and experimental studies are needed to enhance the performance and expand the operating range of ammonia-fuelled engines. This study investigates the feasibility of introducing ammonia to dual-fuel compression-ignition engine, where a pilot dose of diesel oil initiates the ignition of ammonia-air mixture. Numerical simulations of the combustion process were carried out using a one-dimensional model, parametrized according to the specifications of a four-cylinder, turbocharged compression-ignition engine with conventional direct injection supply system, modified slightly for ammonia induction. The model was validated by comparison with empirically determined data. The simulations were performed for different combinations of ammonia-diesel oil ratios at various engine load. Ammonia was treated as an energy replacement for diesel oil. Engine performance and emissions of selected pollutants in dual-fuel operation mode were compared to that with diesel oil only. The results showed that different ammonia-diesel oil ratios can be used to achieve the same engine torque. A higher than rated power, depending on engine load conditions, can be obtained with the addition of an extra dose of ammonia. The influence of ammonia on the emissions of particular pollutants varied and was discussed in detail. Acquired combustion characteristics and engine performance parameters allow for a positive verification of the proposed model. The drawn conclusions may be useful for the development of dual-fuel engine control algorithms.

1 August 2019 in Journal of the Energy Institute
Verified
Journal Article
Closed access
MBMateusz Bednarski
Mateusz Bednarski
OPOrliński Piotr
Orliński Piotr
MWMarcin Krzysztof Wojs
Marcin Krzysztof Wojs
MSMieczysław Sikora
Mieczysław Sikora

11 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
Maciej GisMaciej Gis
Maciej Gis
MBM Bednarski
M Bednarski
To better reflect real-world emissions of harmful exhaust, substances from light-duty vehicles, the WLTP cycle (World Light Test Procedure) was introduced in laboratory tests. This article discusses that test and conditions for its implementation in the context hitherto in force of the NEDC cycle (New European Driving Cycle). The article presents results of emission tests of two vehicles: one hybrid (electric motor + spark ignition combustion engine) and the other with an internal combustion engine with similar rated powers in the above-mentioned WLTP cycle. Reference is made mainly to the gaseous pollutant road emissions, i.e.: CO, CO2, THC, NOX. A comparison of the above emission with the one obtained for both vehicles in the NEDC cycle was also made.

30 October 2025 in Combustion Engines
Verified
Journal Article
Open access
MBMateusz Bednarski
Mateusz Bednarski
MSMieczysław Sikora
Mieczysław Sikora
OPOrliński Piotr
Orliński Piotr
The advancement of combustion engines is driven by stricter emission regulations (e.g., Euro/EPA standards), requiring innovations in lubrication. Modern oils must ensure wear protection, emission system compatibility (e.g., DPFs) and fuel efficiency. This paper analyzes updates to ACEA, API, and OEM specifications, focusing on oxidation resistance, low-SAPS formulations, and fuel economy. The trend toward low-viscosity oils (0W-20, 0W-16) reduces friction but challenges lubrication under high loads. The study evaluates these changes’ impact on engine durability and future oil development amid tightening sustainability and emission norms. This article will analyze lubricant requirements for passenger cars.

1 June 2021 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
MSMieczysław Sikora
Mieczysław Sikora
OPOrliński Piotr
Orliński Piotr
MBMateusz Bednarski
Mateusz Bednarski
The research was divided into two stages. The first stage of work was to perform empirical research using the Perkins engine. The test stand was equipped with an exhaust gas composition analyzer, a pressure sensor enabling measurement of pressure in the engine cylinder and a crankshaft position...

13 April 2024 in Combustion Engines
Verified
Journal Article
Open access
OPOrliński Piotr
Orliński Piotr
MSMieczysław Sikora
Mieczysław Sikora
MBMateusz Bednarski
Mateusz Bednarski
PLPiotr Laskowski
Piotr Laskowski
Maciej GisMaciej Gis
Maciej Gis
PWPiotr Wiśniowski
Piotr Wiśniowski
The article carries out a detailed analysis and evaluation of indicators related to the combustion process (pressure and temperature in the engine combustion chamber, heat release rate, heat release fraction) in a JCB 444 TA4i compression-ignition engine fuelled with diesel and hydrogenated vegetable oil (HVO). During the empirical tests, the operation of the exhaust gas recirculation (EGR) system was stopped and no other changes were made to the engine settings (factory settings were used). In the first stage, the empirical tests were carried out at speed characteristics on an engine dynamometer. Then, an experiment was carried out at the engine crankshaft speed corresponding to the maximum torque - which consisted of determining the indicators related to the combustion process at a constant mass flow of fuel: diesel and HVO fuel. This provided information on the effect of hydrogenated vegetable oil on the combustion process in relation to the diesel engine feed. The conclusions drawn from the empirical study can be used to develop guidelines to change the operating map of a compression-ignition engine when it is fed with hydrogenated vegetable oil.