26 October 2017 in IEEE Transactions on Device and Materials Reliability
The superior electro-thermal properties of silicon carbide (SiC) power devices permit higher temperature of operation and enable higher power density compared with silicon devices. Nevertheless, the reliability of SiC power modules has been identified as a major area of uncertainty in applications which require high reliability. Traditional power module packaging methods developed for silicon chips have been adopted for SiC and the different thermomechanical properties cause different fatigue stresses on the solder layer of the chip. In this paper, a 2-D finite element model has been developed to evaluate the stress performance and lifetime of the solder layer for Si devices, which has been validated using accelerated power cycling tests on Si IGBTs. The proposed model was extrapolated for SiC devices of the same voltage and current rating using the same solder material and the results show that under the same cyclic power loss profile the induced stress and strain energy in the die attach layer is much higher and concentrates on the die/solder interfacial area for SiC chips. Using the validated stress-based model, the lifetime can be quantified when SiC chips are used. This ability to extrapolate the available power cycling and lifetime data of silicon chips to SiC chips would be a key element for developing reliable packaging methods for SiC devices.
10 December 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
17 December 2020 in IEEE Transactions on Power Electronics
Power semiconductor chips are paralleled in modules to increase current rating. Under thermo-mechanical stresses in service, the die-attach solder layers will gradually develop into different levels of degradation. Early fault detection requires to monitor the occurrence of such an uneven degradation pattern. Internal temperature differences only slightly affect the current sharing between chips, and some temperature sensitive electric parameters (TSEPs) are considerably weakened at module terminals. This paper presents an external heat-flux based condition monitoring method, implemented in a two-stage neural network. The first stage consists of a set of sub-networks to represent the mapping between the electrical operating point of the module and its external temperature distribution, for a range of solder degradation patterns and severities. The respective levels of matching are then extracted and applied to the second stage to diagnose the health condition of the power module. This condition monitoring method, validated by experiment, can sensitively detect individual solder degradation in multi-chip power modules or multi-module power electronic systems.
8 July 2022 in IEEE Transactions on Power Electronics
State-of-the-art soft-switching modulations such as critical conduction mode and triangular current mode increase the conduction loss of power semiconductors and require variable switching frequencies; thus, these soft-switching methods are seldom used in high-power dc–ac conversion. To achieve soft-switching while maintaining low root mean square currents, this article proposes a hybrid quadrilateral and continuous current mode (HQCCM) modulation for general high-frequency single-phase dc–ac conversion based on paralleled silicon carbide metal oxide semiconductor field-effect transistors. The proposed HQCCM adaptively operates in soft-switching quadrilateral current mode or hard-switching continuous conduction mode in one ac line cycle depending on the instantaneous ac load current. Thus, high efficiencies can be achieved over the full power range. This HQCCM modulation features adaptive soft-switching, constant switching frequency, and compatibility to line filter and is applicable for high-power applications. A 4.4-kW single-phase dc–ac inverter is developed and tested to verify the advantages of the HQCCM. This article is accompanied by a video demonstrating the effectiveness of the proposed HQCCM in varying load scenarios.
6 May 2024 in IEEE Transactions on Power Electronics
This article proposes a new power electronic packaging for discrete dies, namely, a standard cell, which consists of a step-etched active metal brazing (AMB) substrate and a flexible printed circuit board (flex-PCB). The standard cell exhibits high thermal conductivity, complete electrical insulation, and low stray inductance, thereby enhancing the performance of SiC mosfet devices. The standard cell has a stray power loop inductance of less than $\text{1}\,\text{nH}$ and a gate loop inductance of less than $\text{1.5}\,\text{nH}$ . The standard cell has a flat body with surface-mounting electrical connections on one side and direct thermal connections on the other. The use of flex-PCB die interconnection enables maximum utilization of source pads while providing a flexible gate-source connection and the converter PCB. This article presents the design concept of the standard cell and experimentally validates its effectiveness in a converter system.
23 February 2024 in IEEE Transactions on Power Electronics
Reducing the thermal resistance is vital for power modules. Thermal conducting paths are formed by heterogeneous layers for insulation, causing inevitably high thermal resistance. In this article, with the aid of direct metallization technology, a direct bonded copper (DBC)-free power module concept is proposed to achieve near-junction water cooling. A 55% reduction of thermal resistance is achieved by using a DBC-free power module instead of a DBC interface. Reliability analysis indicates that the DBC-free power module is sufficiently reliable in terms of mechanical stress, fatigue, and peel strength. The junction temperature of the DBC-free power module is experimentally compared to indirectly and directly water-cooled power modules with the DBC interface. The proposed near-junction water cooling method has effectively achieved reductions of 28 °C and 11 °C in junction temperature, respectively, under full load conditions when compared to the designs of indirectly and directly water-cooled power modules. The maximum junction temperature rise Δ T j of the indirectly water-cooled power module is reduced from 50 °C to 21 °C. The unlimited promise of direct metallization technology in 3-D packaging is also highlighted.