Luke Shillaber

Luke Shillaber

Auto-generated profile, based on publicly available information

Luke Shillaber

Electrical Engineering Division, Department of Engineering, University of Cambridge, Cambridge, U.K.

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 October 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YSYanfeng Shen
Yanfeng Shen
YJYunlei Jiang
Yunlei Jiang
Hui ZhaoHui Zhao
Hui Zhao
LSLuke Shillaber
Luke Shillaber
Chaoqiang JiangChaoqiang Jiang
Chaoqiang Jiang
TLTeng Long
Teng Long
This paper proposes a generic zero-voltage switching (ZVS) scheme for parallel power MOSFETs. Uncoupled or inversely-coupled differential-mode (DM) commutation inductors are added to the midpoints (AC terminals) of parallel MOSFET half-bridges (HBs), and a time-delay-based control scheme is applied, generating a circulating current flowing through these commutation inductors. Thus, the inductor currents are reshaped as quadrilaterals, which enable all the parallel transistors to achieve ZVS. The mode of operation of the proposed paralleling technique is entitled quadrilateral current mode (QCM) due to the quadrilateral-shaped commutation inductor currents. The operating principle of the QCM-paralleling technique is detailed mathematically, yielding accurate closed-form analytical expressions for modulation parameters. Finally, simulations and experimental results of a QCM-enabled synchronous Buck dc-dc converter are presented to validate the theoretical considerations.

21 June 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
LSLuke Shillaber
Luke Shillaber
YJYunlei Jiang
Yunlei Jiang
LRLi Ran
Li Ran
TLTeng Long
Teng Long
In an effort to reduce switching loss, increase switching frequencies, and shrink passive component sizes, power device switching times are being pushed into nanosecond and subnanosecond intervals. However, these fast switching times require high rates of change of current making the power devices susceptible to overvoltage damage from parasitic inductance in the power loop. This presents challenges in measuring the device switching current accurately and, in turn, makes accurate measurements of device switching energy and stored charge difficult. Traditional current measurement methods either do not have the required frequency response to view the switching edge accurately or have a high parasitic inductance that can significantly alter switching performance and cause damage to the power device. In this article, an active current measurement system is developed. This circuit achieves up to 1.6-GHz bandwidth with zero overshoot. By utilizing mutual inductance cancellation, an insertion inductance down to 20 pH has been achieved. The research performed in this article thereby allows for an accurate measurement of device switching loss with minimal power circuit disturbance. The performance of this current measurement is experimentally verified in the frequency domain using a vector network analyzer, and time-domain switching measurements are compared with state-of-the-art current measurement.

29 January 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YSYanfeng Shen
Yanfeng Shen
LSLuke Shillaber
Luke Shillaber
Hui ZhaoHui Zhao
Hui Zhao
YJYunlei Jiang
Yunlei Jiang
TLTeng Long
Teng Long
Parallel connection of GaN high-electron-mobility transistors (HEMTs) is commonly used to achieve higher current ratings. However, at light loads, the switching loss becomes dominant and the overall power conversion efficiency drops sharply. To reduce the light-load switching loss, this paper proposes a desynchronizable paralleling scheme. The midpoint of each paralleled half bridge is connected with a commutation inductor for two operation modes: synchronous and asynchronous. The synchronous mode is activated at heavy loads to share the high current; the added commutation inductors lead to better current sharing than the direct parallel. At light loads, the paralleled devices are desynchronized to generate a circulating current flowing through the commutation inductors. The circulating current enables the lagging HEMTs to achieve the zero-voltage switching (ZVS) and allows the leading ones to turn on at a lower current, thereby significantly reducing the total switching loss. In addition, a thermal balancing scheme is proposed to alleviate the thermal stress imbalance between the desynchronized GaN HEMTs. The operating principle and design guidelines of the desynchronizable paralleling scheme are detailed. Experimental results from multi-pulse and continuous tests are provided to verify the advantages of the proposed paralleling scheme in reducing light-load switching loss and improving light-load efficiency.

21 June 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
TLTim Lackie
Tim Lackie
YJYunlei Jiang
Yunlei Jiang
LSLuke Shillaber
Luke Shillaber
TLTeng Long
Teng Long
Employing high switching speed wide bandgap (WBG) devices improves the efficiency of industrial drive inverters, but can result in motor overvoltages for shorter lengths of cable between the inverter and motor. These overvoltages are caused by high frequency impedance mismatches resulting in reflection of the voltage pulse edges of the inverter output. Forwards and backwards travelling reflections interfere and in the worst case cause double the DC-link voltage to appear across the motor terminals. In this paper this doubling of the motor voltage stress is observed with only a 10 metre cable. To mitigate the motor overvoltage a novel method using a differential mode coupled inductor between the paralleled half bridges and the phase output is proposed. By adding a delay time between the half bridges at every switching event a quasi-three-level output is produced which can actively cancel reflected voltage waves, eliminating the cause of motor overvoltages. The method can be utilised for three phase inverters, and when using independently driven paralleled devices only requires one additional inductor per phase. A design process for the coupled inductors is given which aims to minimise the circulating current between the half bridges and therefore give minimal increase in conduction losses due to imbalanced current sharing. These additional conduction losses and other limitations of the proposed method are analysed. An inverter utilising this proposed method is implemented and compared to a passive filter designed for overvoltage mitigation. The novel method achieves near perfect overvoltage mitigation with much smaller additional volume and much lower losses than the filter. Furthermore the losses when using the active mitigation method are very similar to using the inverter with no overvoltage mitigation.

21 August 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YWYulei Wang
Yulei Wang
TLTeng Long
Teng Long
MZMingrui Zou
Mingrui Zou
PSPeng Sun
Peng Sun
JGJiakun Gong
Jiakun Gong
ZZZheng Zeng
Zheng Zeng
Rogowski coil (RC) has been commonly employed in power electronics due to its benefits of galvanic isolation, high-current measurement capability, and simple integration. However, the bandwidth of RC is restricted to tens of MHz because of the inextricable resonance issue caused by its self-inductance and parasitic capacitance. This limitation hinders the ability of the RC to measure fast current transients such as those of wide-bandgap (WBG) power devices. In this letter, the concept of transmission line Rogowski coil (TL-RC) is proposed to address the limitations of inductance and capacitance. The design criteria of double-ended impedance matching are further derived to ensure optimal signal integrity of TL-RC at GHz levels. These two concepts jointly form the isolated current sensor design with a bandwidth exceeding 3 GHz. Comparative experiments confirm the ultrafast and isolated advantages of the TL-RC for the WBG applications.

8 July 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Open access
YJYunlei Jiang
Yunlei Jiang
YSYanfeng Shen
Yanfeng Shen
LSLuke Shillaber
Luke Shillaber
BHBorong Hu
Borong Hu
Chaoqiang JiangChaoqiang Jiang
Chaoqiang Jiang
TLTeng Long
Teng Long
State-of-the-art soft-switching modulations such as critical conduction mode and triangular current mode increase the conduction loss of power semiconductors and require variable switching frequencies; thus, these soft-switching methods are seldom used in high-power dc–ac conversion. To achieve soft-switching while maintaining low root mean square currents, this article proposes a hybrid quadrilateral and continuous current mode (HQCCM) modulation for general high-frequency single-phase dc–ac conversion based on paralleled silicon carbide metal oxide semiconductor field-effect transistors. The proposed HQCCM adaptively operates in soft-switching quadrilateral current mode or hard-switching continuous conduction mode in one ac line cycle depending on the instantaneous ac load current. Thus, high efficiencies can be achieved over the full power range. This HQCCM modulation features adaptive soft-switching, constant switching frequency, and compatibility to line filter and is applicable for high-power applications. A 4.4-kW single-phase dc–ac inverter is developed and tested to verify the advantages of the HQCCM. This article is accompanied by a video demonstrating the effectiveness of the proposed HQCCM in varying load scenarios.