22 January 2016 in IEEE Electron Device Letters
An on-chip resonator is designed and fabricated using a standard 0.13-μm SiGe technology for millimeter-wave applications. The designed resonator is based on a unique structure, which consists of two broadside-coupled meander lines with opposite orientation. The equivalent LC circuit of the resonator is given, while the impact of the structure on the resonance frequencies is investigated. Using this structure along with capacitors, a compact bandpass filter (BPF) is also designed and fabricated. The measured results show that the resonator can generate a resonance at 57 GHz with the attenuation better than 13.7 dB, while the BPF has a center frequency at 31 GHz and a insertion loss of 2.4 dB. The chip size of both the resonator and the BPF, excluding the pads, is only 0.024 mm 2 (0.09×0.27 mm 2 ).
20 September 2016 in IEEE Electron Device Letters
A compact balanced frequency doubler with more than 35 dB odd-harmonic rejection and fractional bandwidth of 73% is presented in this letter. Wide bandwidth and high odd-harmonic suppression is achieved by adopting a new technique for the transformer balun design, resulting in a very low magnitude imbalance of 0.13 dB and a phase imbalance of 0.4° over 7-15 GHz. The balun performance is improved by offsetting the radius of the primary and secondary coils, which reduces the parasitic coupling capacitance. The input and output frequency ranges for the doubler are 7-15 GHz and 14-30 GHz respectively. The circuit was fabricated in 0.13-μm SiGe technology. The chip size is 0.6 mm × 0.4 mm.
18 January 2016 in IEEE Transactions on Microwave Theory and Techniques
A higher frequency, over 2 GHz, is suggested for current 4G or 5G wideband applications. By adopting a unique gain control method, an analog-controlled variable-gain amplifier (VGA) with an accurate dB-linear characteristic is presented. The designed VGA not only features large bandwidth, but also has accurate gain adjustment with a relatively wide control voltage range. The VGA has a measured gain range of 24 dB, of which 17.3 dB is dB-linear with less than ±0.3-dB gain error. The -3-dB bandwidth is relatively constant from 2 to 2.2 GHz for the entire dB-linear range. An output 1-dB compression point of 1.8 dBm and a noise figure of 24 dB are measured. Due to the simple structure, the current consumption of the VGA core is only 2.9 mA from a 1.2-V supply, and the size is only 225 μm×45 μm, excluding pads. Moreover, the robustness of the designed VGA is verified by means of Monte Carlo simulation.
3 April 2014 in IEEE Transactions on Electron Devices
The thermal impact of device bias-state and structures (such as source connected field plates, gate-pitch, back-vias, and number of gate fingers) in AlGaN/GaN-on-Si high electron mobility transistors (HEMTs) are measured using gate metal resistance thermometry (GMRT). The technique characterizes the thermal response of device gate metallization to determine the gate-epilayer junction temperature (T j ), which is directly influenced by the channel heat source due to its close proximity. It is found that low gate leakage levels in GaN HEMTs make them favorable candidates for GMRT. Bias-dependent self-heating, independent of power dissipation, is observed in the devices. Therefore, T j of different device configurations are compared at constant bias state, as well as constant power density (3.75 W/mm) to improve accuracy. T j reduction is observed at high drain bias due to the migration of the channel heat source toward the gate field plate edge. This provides independent experimental validation for a reported electrothermal model [7]. A 3-D thermal finite element method model is presented, which simulates measured T j rise to within ~6% across a range of device configurations and operating conditions. This is ultimately made possible upon implementation of a thermal boundary resistance layer and extraction of its temperature response using GMRT data.
29 August 2013 in IEEE Transactions on Electron Devices
Gate junction temperature is presented as the crucial parameter for modeling thermal degradation in GaAs device reliability studies, and sufficient for modeling the impact of temperature on device terminal characteristics. Gate metal resistance thermometry (GMRT) is applied to a GaAs pseudomorphic high-electron mobility transistor to measure its gate junction temperature. It is found that gate leakage current due to impact ionization can interfere with dc GMRT measurements. To the best of our knowledge, for the first time it is demonstrated that this can be largely avoided by instead applying an ac version of GMRT. However, the dynamic resistance of the gate leakage current path can interfere with ac GMRT. Measurements and thermal finite element method simulations of devices at constant power dissipation conclude that the bias dependence of the channel heat source profile affects the gate junction temperature. A parameter extraction technique is presented and used in device lifetime calculations to demonstrate MTTF variations of more than an order of magnitude (despite fixed power) due to bias-dependent self-heating.