10 May 2016 in IEEE Transactions on Power Electronics
This paper presents a flying-capacitor modular multilevel converter (FC-MMC) based on series-connected submodules. It is intended for completely improving the performance of a medium-voltage motor drive system in the entire speed range especially at zero/low speed under rated torque condition. The proposed FC-MMC circuit is characterized by the cross connection of upper and lower arm middle taps through a flying capacitor in per phase leg. By properly controlling the ac current flowing through the flying capacitor, the power balance between upper and lower arms is achieved, leading to very small voltage ripples on submodule dc capacitors in the entire speed range from standstill to rated speed even under the rated torque condition. Meanwhile, no common-mode voltage is injected. Simulation results obtained from a 4160-V 1-MW model show that the proposed FC-MMC along with the proposed control method performances satisfactorily in dynamic and static state even when operated at zero/low speed. Experiments on a downscaled prototype also prove the effectiveness of the proposal.
29 March 2016 in IEEE Transactions on Industrial Electronics
This paper presents an active cross-connected modular multilevel converter (AC-MMC) based on series-connected half-bridge modules. It is intended for completely enhancing the performance of a medium-voltage motor drive system in the full speed range from standstill to rated speed under all load conditions. The proposed AC-MMC circuit is characterized by the cross connection of upper and lower arm middle taps through a branch of series-connected half-bridge converters, which have an identical voltage and current rating with the submodules in the upper and lower arms. This cross-connected branch provides a physical power transfer channel for the upper and lower arms. By properly controlling the amount of high-frequency current flowing through the cross-connected branch, the power balance between the upper and lower arms is achieved even at a zero/low motor speed under constant torque condition. Meanwhile, no common-mode voltage is introduced in the whole speed range. A control strategy with focus on submodule capacitor voltage control is also proposed in this paper to guarantee the normal converter operation. Simulation results obtained from a 4160-V, 1-MW model verify the feasibility of the proposal. Experiments on a downscaled prototype also confirm the validity of the novel circuit and the associated control strategy.
27 May 2020 in IEEE Transactions on Power Electronics
Multiple insulated gate bipolar transistor (IGBT) open-circuit faults severely affect the reliable operation of modular multilevel converters (MMCs). The existing literatures have not provided an effective diagnosis algorithm for MMCs when multiple IGBT open-circuit faults simultaneously appear in one arm. This paper presents a diagnosis strategy to handle that condition. Fault detection and estimation of the faulty submodule (SM) number is implemented by checking the value of the arm voltage error. The faulty SMs are located by observing when the transition of their switching functions leads to an obvious change of the arm voltage error. Meanwhile, the errors between the measured and predicted capacitor voltages are utilized to accelerate the localization. All of the faulty SMs can be quickly located one by one within several control cycles by using the proposed localization method. Simulation and experimental results demonstrate the validity of the proposed diagnosis strategy.
17 August 2017 in IEEE Transactions on Power Electronics
The flying-capacitor modular multilevel converter (FC-MMC) overcomes the low/zero-speed operation issues of conventional MMC-based drive. The FC-MMC injects no common-mode voltage (CMV) to the drive system. However, the pulse width modulator (PWM) introduces switching ripples, which appear as CMV on motor stator windings. To completely get rid of the CMV, an elimination method based on a new modulation scheme is proposed in this paper. The modulation algorithm places the switching pulses end to end for upper and lower arms, respectively. The consistent switching positions between upper and lower arms lead to the complete CMV elimination for FC-MMC-based drive system in entire speed range. Although the proposed method slightly increases the switching frequency as compared to conventional phase-shifted PWM, it is still acceptable in medium-voltage applications. The validation of the proposal is proved by simulations and experiments.
15 January 2018 in IEEE Transactions on Industrial Electronics
Delta-channel modular multilevel converter (MMC) proved successful for zero/low-fundamental-frequency operation without injecting common-mode voltage. However, its application in a medium-voltage variable-speed motor drive is not verified. This paper develops a variable-speed motor drive system based on a delta-channel MMC. The converter power losses together with the compensation strategies are analyzed, and accordingly the submodule capacitor voltage controls are elaborated. The converter controls cascaded with the advanced motor control form the entire control scheme for the drive system. The system performances are tested based on a 4160-V 1-MW simulation model and 208-V 5-kW experimental setup. The results show that the delta-channel MMC along with the proposed control algorithm performs satisfactorily in a driving motor from standstill to a rated speed even under rated torque condition.
31 December 2021 in IEEE Transactions on Power Electronics
SiC mosfet s with packages of common source inductance (TO-247-3) and kelvin source connection (TO-247-4) are both widely used devices in the existing power conversion. Transient analysis of switching characteristics reveals some evaluation mistakes and misguidance design by using the conventional test circuit due to the difference packages. However, the more precise gate characteristic of TO-247-3 SiC mosfet can be obtained by using TO-247-4 device package. Based on the unique feature, this article provides an improved evaluation method to get a comprehensive comparison of TO-247-3 and TO-247-4 SiC mosfet commutation as the active and passive switch devices in the typical half-bridge circuit. The results indicate that 4-PIN SiC mosfet has both advantages of low switching loss and reduced d v /d t. Furthermore, this article first reveals that the widely used drive design for TO-247-3 mosfet with active miller clamped drive IC has a potential irrational circuit defect. Mathematical model analysis and experiment test have been accomplished to verify the superiority of the improved evaluation method. TO-247-4 SiC mosfet is more promising in application of high efficiency, high frequency as well as strict EMI requirement.