Junning Jiang

Junning Jiang

Auto-generated profile, based on publicly available information

Junning Jiang

Nvidia Corporation, Santa Clara, CA, USA

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
DZDadian Zhou
Dadian Zhou
JJJunning Jiang
Junning Jiang
QLQiyuan Liu
Qiyuan Liu
ESEric G. Soenen
Eric G. Soenen
MKMartin Kinyua
Martin Kinyua
JSJose Silva-Martinez
Jose Silva-Martinez
A digitally assisted high-current low-dropout (LDO) regulator is proposed in this article. The LDO architecture combines two main types of regulators: digital LDOs and analog LDOs. The proposed architecture uses the digital loop for tracking large output current variations and the analog loop for steady-state operation. The dual loops have a loop controller for coherent operation. Hence, the proposed LDO inherits some advantages from both sides. It achieves high power supply rejection (PSR) from the analog part without ripples at the output. Compared with the analog loop, the digital loop has a faster settling time while consuming minimum static power. In this design, the maximum load is 245 mA. The PSR is -42 dB at 1 MHz for heavy loading conditions. The quiescent current (IQ) is 300 μA. When the 300-/100-ns (rising/falling) current step is applied at the load, the voltage peak is 71/37 mV, respectively. The proposed LDO achieves a competitive 7.4-ps figure of merit (FOM). The active area is approximately 0.056 mm 2 in a TSMC40-nm process.

1 August 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
JJJunning Jiang
Junning Jiang
Jusung KimJusung Kim
Jusung Kim
AKAydin Ilker Karsilayan
Aydin Ilker Karsilayan
JSJose Silva-Martinez
Jose Silva-Martinez
A highly linear I-channel receiver prototype is presented for a 3-6-GHz broadband radio system with a 200-MHz baseband bandwidth and verified to operate under congested spectrum environments. A direct conversion receiver developed from this prototype is suitable for a cognitive radio, a fifth-generation (5G) receiver, and other wireless systems with a total (in-band signal plus blocker) power of above -6.0 dBm. The broadband receiver consists of a low-noise transconductance amplifier (LNTA), a passive mixer, a wideband transimpedance amplifier, and a power-efficient minimally invasive baseband filter. The LNTA with high linearity employs a cross-coupled structure and resistive degeneration to achieve low noise and high linearity simultaneously. The common-gate-based LNTA achieves 2.3-dB noise figure in simulation. Fabricated in a mainstream 40-nm CMOS technology, the worst case measured system noise figure is under 5.8 dB at 3-MHz baseband frequency, and the conversion gain is larger than 12.8 dB with passband variations under 2 dB from 1- up to 200-MHz signal bandwidth. Over 3-6 GHz, the receiver's in-band input third-order intercept point (IIP3) and input P1db are higher than 15.1 and 3.0 dBm, respectively, whereas the power consumption varies from 64.1 to 69.6 mW.

12 July 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
DZDadian Zhou
Dadian Zhou
CBCarlos Briseno-Vidrios
Carlos Briseno-Vidrios
JJJunning Jiang
Junning Jiang
CPChulhyun Park
Chulhyun Park
QLQiyuan Liu
Qiyuan Liu
JSJose Silva-Martinez
Jose Silva-Martinez
A pipeline analog-to-digital converter (ADC) with high power efficiency is implemented in this paper. The ADC architecture consists of 3.5b, 3.5b, 3.5b, and 4b sub-ADCs. For the first three stages, a current-reuse technique is employed in the current mode multiplying digital-to-analog converters (MDACs). An operational transconductance amplifier (OTA) converts an input voltage into current; A current-steering DAC reuses the OTA bias current. The OTA and the DAC generate the sub-ADC residue in a current domain. As a result, both power consumption and thermal noise for the MDAC are reduced. A transimpedance amplifier (TIA) with a feedback resistor is utilized to convert the current signal to a voltage residue signal for the next stage. An off-chip calibration scheme is used to correct interstage gain and nonlinearity errors. The fabricated ADC achieves 68.1 dB signal-to-noise-and-distortion ratio (SNDR) and 82.3 dB spurious free dynamic range (SFDR) for a sinusoidal input at 4.17 MHz. The ADC operates at a maximum sampling frequency of 260 MHz. With an input signal at 123.129 MHz, the measured SNDR/SFDR are 66.3/78.22 dB, respectively. The total power consumption for the ADC running at maximum speed is 15.38 mW. Thus, the pipeline ADC achieves a 167.4 dB figure-of-merit (FoM). The chip was manufactured in a TSMC 40-nm CMOS process.

15 April 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
TYTanwei Yan
Tanwei Yan
JJJunning Jiang
Junning Jiang
JSJose Silva-Martinez
Jose Silva-Martinez
This paper proposes a fractional spur cancellation technique designed for fractional-N frequency synthesizers. A time domain quantitative analysis is conducted to provide an intuitive understanding of the origin of fractional spurs and to formulate the relationship between the phase error of the feedback signal and the division factor of the frequency divider. By utilizing a dual loop charge-pump based architecture that generates two feedback phases, one leading and one lagging the reference phase, the two loops effectively clamp the reference phase between the two feedback phases and inject complementary charge components to achieve spur reduction. Unlike conventional methods, the proposed analog spur cancellation technique eliminates the need for additional signal processing stages within the loop. This offers several advantages, including reduced complexity, no introduction of additional distortion sources, and minimal impact on loop dynamics. Simulation results employing TSMC 40nm technology demonstrate that the proposed technique can achieve a worst-case fractional spur level of -96.6dBc in a charge-pump based fractional-N frequency synthesizer, offering moderate immunity to mismatches while also slightly improving the phase acquisition time and jitter performance.