30 June 2010 in Optics Express
We designed, manufactured and characterized two birefringent microstructured fibers that feature a 5-fold increase in polarimetric sensitivity to hydrostatic pressure compared to the earlier reported values for microstructured fibers. We demonstrate a good agreement between the finite element simulations and the experimental values for the polarimetric sensitivity to pressure and to temperature. The sensitivity to hydrostatic pressure has a negative sign and exceeds −43 rad/MPa × m at 1.55 μm for both fibers. In combination with the very low sensitivity to temperature, this makes our fibers the candidates of choice for the development of microstructured fiber based hydrostatic pressure measurement systems.
6 January 2012 in IEEE Photonics Technology Letters
We present fiber Bragg grating (FBG)-based hydrostatic pressure sensing with highly birefringent microstructured optical fibers. Since small deformations of the microstructure can have a large influence on the material birefringence and pressure sensitivity of the fiber, we have evaluated two microstructured fibers that were made from comparable fiber preforms, but fabricated using different temperature and pressure conditions. The magnitude and sign of the pressure sensitivity are found to be different for both fibers. We have simulated the corresponding change of the Bragg peak separation with finite-element models and experimentally verified our results. We achieve very high experimental sensitivities of -15 and 33 pm/MPa for both sensors. To our knowledge, these are the highest sensitivities ever reported for birefringent FBG-based hydrostatic pressure sensing.
12 September 2018 in Optics Letters
In this Letter, it has been shown that the twisting of TFBGs (tilted fiber Bragg gratings) decreases their sensitivity to the polarization of the input light. It has been proved by a theoretical simulation study that twisting the TFBG by 180° eliminates the sensitivity of the grating to input light polarization changes. We have experimentally proved that our structure produced has an 18 times lower coefficient of variation of transmission for polarization changes than the untwisted TFBG. This Letter also presents a new method for manufacturing the twisted tilted fiber Bragg grating (TTFBG). We have demonstrated the possibility of writing the TTFBG structure twisted by 90° on a fiber with a length of 10 mm. The structure has been further twisted in the other direction by 90°, which is consistent with a structure twisted by 180°. The properties of both structures were determined. Due to the fiber’s strength, the TTFBG twisted by 180° has to be 2 cm long. An advantage of the proposed method of producing the TTFBG is that there is a twist of the structure itself after fabrication. This creates new possibilities of using the structure in many applications. This type of grating can be used to reduce the sensitivity to polarization in various sensing applications, in particular, to measure the refractive index. In addition, a 180° twisted TTFBG has properties of direction discrimination in twist sensing applications.
15 November 2012 in Optics Express
We present the results of theoretical and experimental characterization of a designed and manufactured dual-mode highly birefringent microstructured fiber. We also demonstrate the measured values of polarimetric temperature and strain sensitivity of both the fundamental and second order modes. As the mode field of the second order mode has a strong interaction with the fiber air holes, we observed a significant (over two orders of magnitude) increase in the polarimetric strain sensitivity of this mode in comparison to the fundamental mode. The enhanced strain sensitivity together with the low temperature sensitivity makes our fiber very attractive for application as extremely sensitive temperature independent strain transducers.
1 December 2010 in Acta Physica Polonica A
6 May 2014 in Journal of Lightwave Technology
An experimental study of the mechanical reliability of microstructured optical fibers (MOFs) is reported. Tensile tests were carried on five types of MOFs and two reference fibers, and the tensile strengths were analyzed using Weibull statistics. Optical microscopy of the surfaces of rupture allowed identifying the critical flaws and determining the failure mechanisms. First, it appears that the MOFs have lower tensile strengths than standard optical fibers. Second, the mechanical strength of MOFs was found to be related to the dimensions and morphology of the microstructure. Finally, fractographic examinations confirmed that MOFs can fail from defects located in the vicinity of the air holes, in contrast to standard optical fibers for which cracks always start propagating from defects located on the outer silica surface.