Gojko Joksimovic

Gojko Joksimovic

Auto-generated profile, based on publicly available information

Gojko Joksimovic

University of Montenegro

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 December 2020 in IEEE Access
Verified
Journal Article
Open access
GJGojko Joksimovic
Gojko Joksimovic
ELEmil Levi
Emil Levi
AKAldin Kajevic
Aldin Kajevic
MMMario Mezzarobba
Mario Mezzarobba
ATAlberto Tessarolo
Alberto Tessarolo
The paper develops a method to choose the number of rotor bars in order to eliminate rotor slot harmonics in stator current spectrum and pulsation torques that are their consequence. Mains-fed, three-phase cage induction motors with the most common number of pole pairs and number of stator slots, that result in integer slot winding, are analyzed. The analysis is based on the recently derived general rule for optimal selection of rotor bars, valid for symmetrical multiphase machine with prime number of phases and integer slot stator winding. As a tool for validation of analytically predicted results, parameterized winding function (PWF) model is used. Electromagnetic torque ripple factor is used as a measure of goodness of the number of rotor bar selection. The practical motivation of the study is an attempt to supersede the many existing rules for rotor bar number selection that, depending on the source, may be different, and provide a unified general approach to the problem. One of the main findings derived in the paper is ascertainment that increasing the number of pole pairs increases the degree of freedom in choosing the proper number of rotor bars. The same applies when the number of motor phases increases.

14 November 2019 in Electrical Engineering
Verified
Journal Article
Closed access
PDF file
GJGojko Joksimović
Gojko Joksimović
JMJuan I. Melecio
Juan I. Melecio
PTPaul M. Tuohy
Paul M. Tuohy
SDSiniša Djurović
Siniša Djurović

24 June 2020 in IEEE Access
Verified
Journal Article
Open access
GJGojko Joksimovic
Gojko Joksimovic
MMMario Mezzarobba
Mario Mezzarobba
ATAlberto Tessarolo
Alberto Tessarolo
ELEmil Levi
Emil Levi
Rules for the selection of rotor bar numbers which minimize current and torque ripples are derived in this paper for a general symmetrical multiphase cage induction machine with prime phase number and integral slot winding. Analytically obtained expressions for optimal rotor bar number selection are validated by means of totally independent simulations, one based on a parameterized winding function (PWF) model of the induction machine and the other employing time-stepping finite-element analysis (TSFEA). As a case study, five-phase four-pole cage induction motors with forty stator slots and different number of rotor bars are comparatively analyzed. Results obtained from the PWF model are in excellent accordance with those independently obtained by TSFEA and both confirm the correctness of the proposed selection criteria. The practical motivation of the study is that an incorrect selection of rotor bar number can lead to parasitic torques of significant amplitude and, presently, there are no general rules available in the literature which may guide designers towards an optimal design choice for a general number of phases.

24 February 2022 in IEEE Access
Verified
Journal Article
Open access
GJGojko Joksimovic
Gojko Joksimovic
PZPeter Zajec
Peter Zajec
ATAlberto Tessarolo
Alberto Tessarolo
VAVanja Ambrozic
Vanja Ambrozic
ARAndraz Rihar
Andraz Rihar
The paper analyzes the influence of the number of rotor bars on the stator current spectral content in a three-phase cage induction motor fed by a pulse-width modulated (PWM) inverter. It is shown that each of the higher-order time harmonics in the supply voltage produces space harmonics in a rotating magnetic flux density wave, which results in induced rotor slot harmonics (RSHs) in the stator current spectrum. The conditions for the existence of these space harmonics are identical to those applying to a mains-fed motor. In other words, the number of rotor bars of a mains-fed motor yielding an RSH-free stator current spectrum produces the same stator current spectrum even in case the motor is inverter-fed. Additionally, to minimize the adverse effects of RSHs in the stator current spectrum, one must consider not only the number of rotor bars, but also its relationship with the frequency modulation ratio of the PWM inverter. Analytical predictions are presented to illustrate these results supported both by numerical simulations of the induction motor modelled through the winding function theory and experimentally taking the case a two-pole cage induction machine as a case study.

3 November 2016
Verified
Conference Paper
Closed access
GJGojko Joksimovic
Gojko Joksimovic
This paper gives the detailed derivation of a parameterized cage induction machine dynamic model in the natural frame of reference. The model is suitable for the analysis of the impact of a different number of rotor bars on machine transients as well as steady state performances. After the initial induction machine design process, for a predetermined number of stator slots and rotor bars, the parameterized model means that any different number of rotor bars could be chosen, resulting in different machine parameters. During this process, the stator winding scheme as well as the rated power of the machine is invariant. The model of the machine is derived by means of winding functions. Thus, in the way described, a very powerful model is obtained that enables the analysis of a dozen of the different number of rotor bars in an hour. The advantage of this is self-evident compared with models based on the finite element method. The power of the model is illustrated by an analysis of a specific machine with three different numbers of rotor bars.

3 October 2024 in IEEE Access
Verified
Journal Article
Open access
GJGojko Joksimović
Gojko Joksimović
HKHamid Ali Khan
Hamid Ali Khan
AKAldin Kajević
Aldin Kajević
The original dynamic model of the synchronous round-rotor generator also known as synchronous turbo-generator (STG) in stand-alone mode of operation is developed and presented in the paper. The model is based on Winding Function (WF) theory and as such it is derived in the natural frame of reference. Depending on the presence or absence of a damper winding on the rotor two independent mathematical models are derived. The presented model provides an accurate description of the real spatial distribution of all windings in the machine, including the short-circuited damper cage winding. Currents in all windings of the machine over time, including all bars of the damper winding, are output from the model. Moreover, the time required to run the model on a computer of average performance is measured in minutes, which is unimaginably fast compared to similar models based on the Finite Element Method (FEM). On the other hand, the results obtained with a completely different and independent time stepping FEM based model largely confirm the validity of the results obtained with the proposed model.