Работа посвящена поиску новых эффективных модифицирующих добавок, позволяющих целенаправленно регулировать технологические свойства битума и физико-механические показатели асфалтобетона на основе комбинаций модификаторов и битума, одновременно являющихся стуктурообразователем многокомпонентного асфальтобетона. Предложено использовать в качестве высокомолекулярных модифицирующих добавок в дорожных битумах блок-сополимер стирола и бутадиена – SBS и сополимер этилена-винилацетата – EVA. Изучено влияние модификаторов Europrene SOL T 6302 на основе бутадиен-стирола и этиленвинилацетатный термопласт марки LG EVA EA 28400 на основе этиленвинилацетата на основные параметры полимерно-битумного вяжущего и эксплуатационные характеристики асфальтобетона. По мере увеличение содержания модификатора в битуме увеличивается глубина погружения иглы и повышается температура размягчения до 58 °С, снижается температура хрупкости до -32-35 °С, значительно расширяется диапазон рабочих температур дорожного покрытия. Исследования показывают, что сополимер SBS является термоэластопластом и дает сравнительно лучшие результаты, чем EVA. В результате исследования адгезионных свойств установлено, что добавление полиэтиленполиамина, содержащего 1,5% MasterLife PVA 100, значительно улучшает совместимость и адгезию битума к минеральным материалам. Однако при увеличении содержания MasterLife PVA 100 выше 2% происходят структурные изменения и ухудшается качество асфальтобетонных покрытий. Исследования показали, что применение полимерного модификатора улучшает многие свойства асфальтобетона. Так, в частности, улучшается тепло- и морозостойкость, износостойкость асфальтобетона в совокупности, влияющие на повышение эксплуатационного срока их службы. По результатам исследования выявлены оптимальные соотношения полимербитумных вяжущих (битум 95,5%+СБС 4%+ MasterLife PVA 100 1,5%) в составе асфальтобетонного покрытия, обеспечивающие их высокие эксплуатационные свойства.
The method of nanomodification was reviewed and its effect on the properties of polymer-bitumen adhesives (PBA) and asphalt concrete prepared on their basis was studied. It was determined that nanomodified PBA is less sensitive to aging processes, which is the result of the peptization of asphaltene-resin complexes in the structure of modified adhesives and their construction with polymer matrix. It has been found that the nanotubes used as modifiers act as a tailoring agent and an inhibitor of aging processes in PBA. It has been determined that when nano-carbon tubes are applied in a complex form with MasterLife PVA 100, a surface-active agent, the adhesion capacity of bitumen increases and, accordingly, the operational properties of asphalt concrete improve. Studies have shown that the most important process in the application of nanomodifier is ensuring its uniform distribution in the volume of bitumen. The process of diffusion of carbon nanotubes in bitumen is carried out at a temperature of 100°C with the presence of a plasticizer. As a result of this operation, it is possible to achieve a uniform dispersion and distribution of nanoparticles in the volume of the carrier medium (plasticizer), which allows to the intensification of the processes of incorporating carbon nanotubes into the composite matrix. Achieving high performance of nanomodified PBA against layering and aging is explained by the processes occurring at the micro and nano levels. Along with the use of plasticizers, ultrasound is also used to introduce nanotubes into the bitumen to break up the nanotube agglomerates (entangled balls of hundreds of carbon nanotubes of different sizes held together by Van der Waals forces) and ensure their uniform distribution in the bitumen. The effect of nanomodified PBA asphalt concrete on strength and deformation properties was studied. It was found that the use of modified adhesives in asphalt-concrete mixtures increases the water resistance, heat resistance, and shear resistance of asphalt concrete.
The possibilities of modification of BNB 50/70 oil road bitumen, which belongs to the category of viscous bitumen and is used in road works in the hot season, at an average temperature not lower than +5°C have been studied. Copolymers of butadiene and styrene and vinyl acetate and ethylene were used as polymer materials for polymer-bitumen adhesives (PBA). A copolymer of butadiene and styrene (SBS) is a synthetic rubber in which solid styrene blocks are linked by butadiene “springs”. When mixed with bitumen, they create a highly elastic structure. The inclusion of 2.5 - 6.0% SBS in bitumen as a polymer additive increases the softening point and frost resistance of bitumen, gives high flexibility to the organic adhesive, which increases the heat resistance and shear resistance of asphalt concrete. Ethylene vinyl acetate (EVA) copolymer forms a rigid network in modified bitumen and resists deformation. It dissolves very quickly in thermoplastic bitumen at a temperature of 155-180°C, which facilitates the process of preparing PBY for asphalt-concrete. The optimal concentration of polymers for obtaining high heat-resistant and flexible PBY has been determined. Carbon nanotubes act as a functional additive for bitumen. Modified bitumen adhesives and physical-mechanical indicators of asphalt-concrete mixtures made on their basis were studied. It was found that by introducing a small amount of nanocarbon tubes into asphalt-concrete, its shear resistance and strength are significantly increased at different temperatures (from 0 to 50°C).
This paper presents the results of an experimental investigation into the influence of the origin and particle size distribution of binary mineral fillers, combined with a polycarboxylate superplasticizer, on the structure and properties of fine-grained basalt fiber-reinforced concrete. It was established that a composition based on silica fume (10%) and a carbonate component (15%) provides a synergistic effect, resulting in the densification of the cement stone and improved mechanical performance. The results demonstrate that reducing the water-to-cement (W/C) ratio to 0.27 through the use of a superplasticizer (≈ 0.8%) promotes the formation of a dense microstructure and increases the compressive strength to 84 MPa. The addition of basalt fibers (4%) enhances crack resistance and the modulus of elasticity through three-dimensional spatial reinforcement. Furthermore, a reduction in porosity of over 20% was observed, alongside improved durability characteristics, including water absorption down to 2.6%, water impermeability up to W14, and frost resistance up to F600. Additionally, partial cement replacement ensures a reduction in CO2 emissions to 340 kg/m3 (over 40%), confirming the environmental efficiency of the developed compositions.
30 June 2026 in Bulletin of Kazakh Leading Academy of Architecture and Construction
The utilization of clay raw materials in combination with industrial by-products, such as phosphorus slag and waste glass, offers an effective approach to expanding the raw material base of ceramic production, reducing environmental impacts, and improving the efficiency of natural resource utilization. This study evaluates the feasibility of using medium-plastic loam from the Sarykemer deposit, granulated phosphorus slag, and ground waste glass in the production of building ceramics and determines the optimal ceramic mass composition to achieve enhanced physical and mechanical properties. The chemical and mineralogical compositions of the raw materials and their influence on the properties of the ceramic body were investigated. Experimental specimens with different component proportions were prepared at a molding moisture content of 20%, followed by drying and firing at temperatures ranging from 900 to 1050 °C. The optimum firing temperature was determined based on the degree of sintering observed on the fracture surface and the physical and mechanical properties of the fired specimens. The optimal ceramic composition was found to consist of 80% loam, 15% phosphorus slag, and 5% ground waste glass. The incorporation of these additives enhanced the sintering process, promoted the formation of a dense ceramic body, and improved the physical and mechanical properties of the material. Specimens fired at the optimum temperature of 1000 °C exhibited a compressive strength of at least 20 MPa. The obtained results demonstrate the effectiveness of utilizing local mineral resources and industrial by-products from the Zhambyl region for the production of wall ceramics, enabling the manufacture of high-quality ceramic materials with improved performance, reduced consumption of natural raw materials, and enhanced environmental sustainability of the production process.