Jens von Wolfersdorf

Jens von Wolfersdorf

Auto-generated profile, based on publicly available information

Jens von Wolfersdorf

University of Stuttgart

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
TKTobias Krille
Tobias Krille
RPRico Poser
Rico Poser
JWJens von Wolfersdorf
Jens von Wolfersdorf
MHMarc Henze
Marc Henze

1 January 2008
Verified
Conference Paper
Closed access
PDF file
SJSean C. Jenkins
Sean C. Jenkins
FZFrank Zehnder
Frank Zehnder
Igor V. ShevchukIgor V. Shevchuk
Igor V. Shevchuk
JWJens von Wolfersdorf
Jens von Wolfersdorf
BWBernhard Weigand
Bernhard Weigand
MSMartin Schnieder
Martin Schnieder
Internal cooling channels with differing aspect ratios are typically found in gas turbine blades due to the varying thickness of the blade from the leading to trailing edge. These serpentine passages often contain several 180° bends, which are sharp edged in the region of the blade tip. The 180° bend has a pronounced effect on the heat transfer characteristics in the outlet channel and tip wall, where a strong influence is seen due to the divider wall-to-tip wall distance in the bend. The present study investigates the effect of the divider wall-to-tip wall distance for a ribbed two-pass cooling channel with a 2:1 inlet and 1:1 outlet channel. Spatially resolved heat transfer measurements were made using the transient thermochromic liquid crystal technique for a smooth and a ribbed configuration using parallel 45° ribs. Effects of the 180° bend on heat transfer and rib-induced enhancements were identified separately and bend effects were found to dominate the heat transfer increase in the outlet channel near the bend. Pressure losses due to the bend and ribs were also independently evaluated for a range of tip wall distances. Results show that the smaller tip wall distances increase heat transfer on the tip wall and outlet channel, but at the cost of an increased pressure loss. An optimum tip wall position is suggested, forming a compromise between heat transfer improvement and increased pressure losses.

1 May 2001 in Annals of the New York Academy of Sciences
Verified
Journal Article
Closed access
PDF file
KHK. Hermanson
K. Hermanson
SPS. Parneix
S. Parneix
JWJ. Von Wolfersdorf
J. Von Wolfersdorf
KSK. Semmler
K. Semmler

13 June 2014
Verified
Conference Paper
Closed access
KMKonrad Makowka
Konrad Makowka
NDNils Droeske
Nils Droeske
JVJiby J. Vellaramkalayil
Jiby J. Vellaramkalayil
TSThomas Sattelmayer
Thomas Sattelmayer
JWJens von Wolfersdorf
Jens von Wolfersdorf

10 November 2021 in Measurement Science and Technology
Verified
Journal Article
Open access
PDF file
SBStefan Brack
Stefan Brack
RPRico Poser
Rico Poser
JWJens von Wolfersdorf
Jens von Wolfersdorf
An experimental approach to study unsteady local heat transfer characteristics due to airflow velocity and/or airflow temperature variations is presented. It uses controlled electrical heaters and rotating vanes to independently vary the flow and thermal boundary conditions. Time-resolved surface temperatures are measured using an in situ calibrated infrared thermography camera. Those surface temperatures are analyzed by modeling the transient conjugate heat transfer process in the wall to obtain locally resolved surface heat flux distributions. The applicability is illustrated for a flow and heat transfer behind a tetrahedral vortex generator on a flat plate.

1 January 2009
Verified
Conference Paper
Closed access
PDF file
MSMarco Schu¨ler
Marco Schu¨ler
FZFrank Zehnder
Frank Zehnder
BWBernhard Weigand
Bernhard Weigand
JWJens von Wolfersdorf
Jens von Wolfersdorf
SNSven Olaf Neumann
Sven Olaf Neumann
Gas turbine blades are often cooled by using combined internal and external cooling methods, where for internal cooling purposes usually serpentine passages are applied. In order to optimize the design of these serpentine passages it is inevitable to know the influence of mass extraction due to film cooling holes, dust holes or due to side walls for feeding successive cooling channels as for the trailing edge on the internal cooling performance. Therefore, the objective of the present study was to analyse the influence of side wall mass extraction on pressure loss and heat transfer distribution in a two-pass internal cooling channel representing a cooling scheme with flow towards the trailing edge. The investigated rectangular two-pass channel consisted of an inlet and outlet duct with a height-to-width ratio of H/W = 2 connected by a 180° sharp bend. The tip-to-web distance was kept constant at Wel /W = 1. The mass extraction was realized using several circular holes in the outlet pass side wall. Two geometric configurations were investigated: A configuration with mass extraction solely in the outlet pass, and a configuration with mass extraction in the bend region and outlet pass. The extracted mass flow rate was 0%, 10%, and 20% of the inlet channel mass flow. Spatially resolved heat transfer distributions were obtained using the transient thermochromic liquid crystal technique. Pressure losses were determined in separate experiments by local static pressure measurements. Furthermore, a computational study was performed solving the Reynolds-Averaged Navier-Stokes equations (RANS method) using the commercial Finite-Volume solver FLUENT. The numerical grids were generated using the hybrid grid generator CENTAUR. Three different turbulence models were considered: the realizable k-ε model with two-layer wall treatment, the k-ω-SST model, and the v2 -f model. The experimental data of the investigation of side wall ejection showed that the heat transfer in the bend region slightly increased when the ejection was in operation, while the heat transfer in the section of the outlet channel with side wall ejection was nearly not affected. After this section a decrease in heat transfer was observed which can be attributed to the decreased mainstream mass flow rate.