6 March 2020 in IEEE Transactions on Power Electronics
Soft magnetic composites (SMCs) based magnetic cores are attractive for high frequency and high power inductor design. The permeability of SMC core can be achieved by adjusting the powder size, addition of insulation material, and forming pressure to reduce the air gap loss and ease the inductor design. The nanocrystalline alloy (Fe-Cu-Nb-Si-B) with high saturation flux density and low hysteresis loss, showing potential suitability for SMC based magnetic cores. To date, nanocrystalline alloys are mostly used in form of laminated ribbons for magnetic cores but seldom used in SMC cores. Neither experimental validation of nanocrystalline powder SMC cores nor comparison with other commonly used SMC cores has been reported. In this paper, the structure and manufacturing process of nanocrystalline powder cores are introduced. The calculation of core loss is defined for the nanocrystalline powder core. The characteristics and performance of the nanocrystalline powder toroidal core are compared with those of other SMC cores such as Fe-Si powder (X flux), Fe-Ni powder (High flux), Fe-Si-Al powder (Kool Mμ), Fe-Ni-Mo powder (MPP). Experimental results at frequencies from 100 kHz to 600 kHz are provided to validate the loss calculation and feasibility of this new nanocrystalline powder core.
18 December 2023 in IEEE Transactions on Power Electronics
Fe-based nanocrystalline ribbon is an alternative to the ferrite for high-frequency magnetic cores due to its low hysteresis loss and high magnetic saturation. The drawback of the Fe-based nanocrystalline ribbon is its high conductivity. Crushing the homogenous ribbon to restructure a nanocrystalline flake ribbon (NFR) can reduce the conductivity while maintaining other superior magnetic properties of the noncrushed nanocrystalline ribbon. So far, several previous works have proven that the NFR can replace the ferrite in the dual active bridge and wireless power transfer system. However, seldom of these works mention the detailed mechanism of the NFR. In this article, the structure and manufacturing process of the NFR are introduced. The effect of the relative permeability and the crushing pattern on the magnetic properties of NFR has been quantitatively reported. A dual-permeability core formed by two types of NFR has been demonstrated for an inductor. Comparison has been made to inductors using the ferrite core (N27, N87, DMR44) in a similar size. Experiment results show that the dual-permeability NFR core has a lower core loss and higher magnetic saturation than the ferrite counterparts at frequencies from 100 to 300 kHz.
27 October 2023 in IEEE Transactions on Power Electronics
This paper examines the performance of a 13kW high-power inductive power transfer system utilising a hybrid core structure with novel nanocrystalline ribbon cores and nanocrystalline flake ribbons. Conventional laminated nanocrystalline ribbon cores exhibit excessive edge losses due to high flux density concentrated on the edge and high eddy current losses in the lateral wall, potentially causing partial thermal runaway. To mitigate this issue, the solution is proposed to employ nanocrystalline flake ribbons as a shielding material on the edge while maintaining the nanocrystalline ribbon core as the main magnetic coupler. The performance of the hybrid core is evaluated under different power levels up to 13.8 kW. Experimental results reveal a nearly 2% increase in peak efficiency compared to the ferrite DMR44 and a 1% increase compared to standalone nanocrystalline ribbon cores, bringing the peak DC-DC efficiency to over 96%. Moreover, under 6.6 kW output power, the temperature rise after 2-hour operation is significantly reduced to a maximum temperature of 76.5°C with the proposed hybrid core, compared to 96.4°C with the ferrite shield and 110.6°C without any edge shield. The design highlights using nanocrystalline material in inductive power transfer systems to improve efficiency and thermal performance.
11 July 2022 in IEEE Transactions on Power Electronics
This letter reports characterization of the novel nanocrystalline flake ribbon (NFR) soft magnetic material. The comparative analysis among the ferrite N87, N27, and the NFR is presented at different temperature, frequency, and peak magnetic flux density, respectively. Experimental results prove that the NFR has lower loss density, higher magnetic flux density saturation, and better temperature stability from 85 to 300 kHz. A LCL resonant tank based circuit is employed for large signal characterization. The mass-based stacking factor of the NFR core is adopted to describe the core structure. This letter suggests that the NFR is a good alternative to the ferrite for high power magnetic cores due to its superior performance and flexibility structures.
26 January 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper proposes the design and analysis of an inductive power transfer (IPT) system that features novel nanocrystalline flake ribbon (NFR) cores. The flake ribbons are produced by compressing the dielectric material with nanocrystalline ribbons, leading to a reduction in the eddy current loss. A complete magnetic core is then fabricated by laminating the ribbons, imparting anisotropic properties. The paper outlines the design methodology for NFR cores, considering this lamination characteristic in Double-D IPTs. Accordingly, NFR cores with a lamination factor of 0.375 and a core thickness of 3.2 mm have been designed, produced, and experimentally validated. The tests indicate an over 95% DC-DC efficiency and an over 96.3% AC-AC efficiency at the output power of 8.9 kW. To assess their thermal attributes, one-hour duration tests at continuous 6.6 kW operation were performed on NFR cores and ferrite groups. Results demonstrate that NFR cores maintain a cooler temperature at 76.4 °C, whereas the DMR44 and DMR95 reach 91.7 °C and 84.9 °C respectively. Additionally, the designed NFR cores have achieved 51% core weight reduction, 31% volume reduction, and 20% thickness reduction. The proposed NFR cores based on the design methodology can greatly enhance high power density IPT systems.
24 February 2019 in IEEE Transactions on Applied Superconductivity
This paper presents the power dissipation analysis on high-temperature superconducting (HTS) coated conductor tapes and coils under the action of various oscillating currents and fields. The loss calculation on HTS coil was carried out by the H-formulation model implemented in the finite-element method (FEM) software package COMSOL Multiphysics. There were four different oscillating (ac) signals in this paper: sine, triangle, sawtooth, and square. Two scenarios causing loss in HTS tapes and coils which have been analyzed: Scenario 1 ac transport current; Scenario 2 ac magnetic field. The simulation results were compared to the experiment results with the typical sinusoidal ac signal.