This paper presents the first reported 28-GHz phased-array IC for 5G communications. Implemented in 130-nm SiGe BiCMOS, the IC includes 32 TRX elements and features concurrent independent beams in two polarizations in either TX or RX operation. Circuit techniques to enable precise beam steering, orthogonal phase and amplitude control at each front end, and independent tapering and beam steering at the array level are presented. A TX/RX switch design is introduced which minimizes TX path loss resulting in 13.5 dBm/16 dBm Op1dB/Psat per front end with >20% peak power added efficiency of the power amplifier (including switch and off-mode LNA) while maintaining a 6 dB noise figure in the low noise amplifier (including switch and off-mode PA). Comprehensive on-wafer measurement results for the IC across multiple samples and temperature variation are presented. A package with four ICs and 64 dual-polarized antennas provides eight 16-element or two 64-element concurrent beams with 1.4°/step beam steering (<;0.6° rms error) across a ±50° steering range without requiring calibration. A maximum saturated effective isotropic radiated power of 54 dBm is measured in the broadside direction for each polarization. Tapering control without requiring calibration achieves up to 20-dB sidelobe rejection without affecting the main lobe direction.
This article reviews current research and development as well as future opportunities for packaging and antenna integration technologies for silicon-based millimeter-wave phased arrays in emerging communication applications. Implementations of state-of-the-art silicon-based phased arrays below 100 GHz are discussed, with emphasis on array architectures for scaling, antenna integration options, substrate materials and process, antenna design, and IC-package codesign. Opportunities and challenges to support phased array applications beyond 100 GHz are then presented, including emerging packaging architectures, interconnect characterization requirements, thermal management approaches, heterogeneous integration of multifunction chiplets, and novel antenna technologies.
20 May 2019 in IEEE Transactions on Microwave Theory and Techniques
Silicon-based millimeter-wave (mm-wave) phased-array technologies are enabling directional wireless data communications at Gb/s speeds. In this paper, we review and discuss the challenges of implementing a multichip phased-array antenna module for mm-wave applications using organic buildup substrate technology. A prototype test vehicle has been fabricated and studied to evaluate the antenna and interconnect performance, dielectric properties, package substrate warpage conditions at different temperatures, chip- and board-level joint process reliability, and thermal management feasibility for cooling. Based on the learning from the test vehicle, an organic-based multilayered phased-array antenna package for 28-GHz mm-wave radio access applications is implemented. The package incorporates 64 dual-polarized antenna elements and features an air cavity common to all antennas. Direct probing measurements on a single-antenna element of the package show over 3 GHz of bandwidth and 3-dBi gain at 28 GHz. A phased-array transceiver module has been developed with the package; the module includes four SiGe BiCMOS ICs attached using flip-chip assembly. Module-level measurements in the TX mode show a 35-dB near-ideal output power increase for 64-element power combining; 64-element radiation pattern measurements are reported with a steering range of ± 50° without tapering in off-boresight directions, and 64-element radiation pattern measurements with tapering show achievement of a sidelobe level lower than -20 dB. The transceiver modules achieved 20.64-Gb/s throughput with 256 QAM and 800-MHz bandwidth in direct over-the-air link measurement results.
27 September 2022 in IEEE Journal of Solid-State Circuits
We present a 24–30-GHz 256-element dual-polarization transceiver (TRX) phased array based on a 16-element beamformer integrated circuit (BF-IC), 2-element frequency conversion integrated circuit (FC-IC), liquid crystal polymer (LCP)-based combiners and filters, and a tileable package with 64 embedded dual-polarized (dual-pol) antennas. The phased array presented in this work overcomes three key challenges in current 5G millimeter-wave (mmWave) antenna arrays: 1) it supports a dramatic increase in the number of supported fast-access beams; 2) it offers improved power efficiency; and 3) it provides a path to lower solution cost. 1) We enable fast switching among $>$ 30 000 beams—orders of magnitude improvement over prior work—by employing an on-chip beam calculator in the BF-IC, achieving 200-ns beam setup and 8-ns over-the-air (OTA)-switching time. 2) We enable a module-level transmitter (TX) mode peak power added efficiency (PAE) of 20% using a modular architecture that preserves power amplifier (PA) linearity and efficiency as well as receiver (RX) mode low noise amplifier (LNA) noise figure (NF). The module achieves Psat effective isotropically radiated power (EIRP) of 68.5 dBm and BF-IC NF $<$ 3.9 dB. 3) We lower the solution cost by enabling a wider steering range to reduce the number of phased arrays required in a sectorized coverage scheme, by reducing the IC and package area, and by avoiding calibration. The wider steering range is enabled by using an in-package magnetoelectric dipole antenna (for the first time in silicon-based phased arrays), resulting in steering over $\pm$ 70 $^\circ$ in H-and V-pol in both E-and H-planes without requiring any calibration. Moreover, the module achieves $>$ 20-dB cross-polarization isolation across the entire $\pm$ 70 $^\circ$ beam steering range.
This article discusses the benefits and challenges associated with the design of multi-function scalable phased arrays at millimeter wave frequencies. First, applications for phased arrays with tens to hundreds of elements are discussed. Existing solutions for scaling silicon-based phased arrays from microwave to terahertz frequencies are reviewed. The challenges and tradeoffs associated with multiple integration options for W-band phased arrays are analyzed, with special consideration given to packaging and antenna performance. Finally, a solution based on SiGe ICs and organic packages for a 64-element dual-polarized 94 GHz phased array is described, along with associated measurement results.
26 May 2021 in IEEE Transactions on Microwave Theory and Techniques
Emerging 5G millimeter-wave (mm-wave) networks use electronic beamforming and beamsteering and support signal bandwidths on the order of hundreds of MHz. Given these characteristics, opportunities exist to develop 3-D sensing applications that leverage 5G mm-wave communications infrastructure. In this context, this work introduces a signal processing pipeline that can: 1) accurately extract the Time of Flight (ToF) of reflected orthogonal frequency division multiplexing (OFDM) communications signals and 2) enhance range resolution by coherently aggregating the reflection information from separate frequency bands. In combination with precise beamsteering, the proposed signal processing techniques enable high-resolution 3-D radar imaging without affecting communications protocols . An experimental system demonstrating this concept has been implemented and is described. This system consists of two software-defined phased array radios (SDPARs), one configured as a prototype 5G base station TX, and one as an auxiliary prototype 5G RX. Each SDPAR primarily consists of a Si-based 28-GHz, 64-element, phased array transceiver module and software-defined radio. Simulation and benchmark results show that our coherent bandwidth stitching enables accurate OFDM-based ranging with 15-cm resolution. Measurement results show 3-D radar images of indoor scenes with 2° angular and 15-cm ranging resolution, created by processing reflected 5G-like communication waveforms at 28 GHz. The produced 3-D radar images effectively depict the location of objects in the scene, and these locations are in close agreement with the ground truth.