12 December 2023 in IEEE Access
Base stations equipped with large multi-antenna systems and associated beamforming schemes provide large capacity and coverage. Massive multiple-input-multiple-output (MIMO) with beamforming was introduced as one of the enablers of 5G system performance, and this technology is evolving with the introduction of more advanced algorithms for spatial multiplexing. One of the most relevant conditions to support deployment of 5G base stations with massive MIMO is to assess realistic RF electromagnetic field exposure compliance distances leveraging the actual maximum approach introduced in IEC 62232:2022. This evaluation method takes into account the variability of traffic load and beam patterns used by the beamforming algorithm. This work investigates the impact of various beamforming schemes, like grid-of-beams, eigen-beamforming and zero-forcing, as well as various array antenna configurations on the evaluation of the power reduction factor used when implementing the actual maximum approach for RF electromagnetic field compliance assessment of massive MIMO base stations. The modelling results show that lower power reduction factors can be considered for eigen-beamforming and zero-forcing beamforming algorithms compared to grid-of-beam. The power reduction factor drop can be up to -4 dB when 8 user equipment’s are connected simultaneously.
12 January 2022 in IEEE Access
The International Electrotechnical Commission (IEC) develops and validates methods for assessing radio frequency electromagnetic field (RF EMF) exposure due to base stations (BS). When the assessment is performed in- situ, it is recommended to extrapolate the maximum level of exposure from measurement of stable signals, such as broadcast signal with BS of the 5 th generation (5G) of mobile communication systems (gNodeB). A comparative statistical analysis of extrapolation methods based on nominal antenna pattern (as measured in an anechoic chamber) and effective antenna pattern (as measured in scattering environment) of gNodeB is presented in this paper. This theoretical analysis shows that extrapolation with nominal antenna pattern may lead to significant overestimation of the maximum RF EMF exposure (up to 5.4 dB) in case of scattering environment or non-line-of-sight (NLOS) conditions. This overestimation is expected to be reduced by using effective antenna pattern in order to better represent the actual propagation conditions, such as those found in urban or dense urban areas. Therefore, it is recommended to perform extrapolation of the maximum exposure based on joint modeling of antenna beam pattern and representative value of the angular spread (AS) for the targeted deployment conditions. This conclusion was obtained from the observed consistence between two different approaches for determination of effective antenna gain. The first approach assumes statistical simulations with full three-dimensional (3D) channel model, especially distribution function of AS. The second approach enables simpler calculation of the effective antenna gain in scattering environment or NLOS conditions by considering only representative values from the full range of AS distribution function. The proposed simple method, if used with representative realistic values of AS, could reduce overestimation of RF EMF exposure resulting from an extrapolation factor based on nominal antenna gains of broadcast and traffic beams.
25 September 2024 in IEEE Access
When performing a radio frequency (RF) electromagnetic field (EMF) exposure assessment of a base station as described in the international standard IEC 62232, the actual maximum approach provides an assessment method based on the actual exposure level, in particular for massive MIMO base stations. Computational modeling can be used to estimate a range of applicable power reduction factors. To date, research studies have generally focused on the channel modeling of actual RF EMF exposure assuming that the attached user equipment (UE) is static. However, in real operational conditions, a UE can be moving and triggering multiple beam changes or beam adaptations. This study provides a computational model applicable to moving UEs and investigates the impact on range of applicable power reduction factors compared to modelling studies using static UEs. The results show that -1.5 dB to -3.5 dB lower power reduction factor can be considered with moving UEs compared to static UEs.
22 August 2024 in IEEE Wireless Communications Letters
To mitigate Electromagnetic Fields (EMF) human exposure from base stations, international standards bodies define EMF emission requirements that can be translated into limits on the “actual” Equivalent Isotropic Radiated Power (EIRP), i.e., averaged over a sliding time window. We aim to enable base stations to adhere to these constraints while mitigating any impact on user performance. Specifically, our objectives are to: i) ensure EMF exposure compliance using actual EIRP control when implementing the “actual maximum approach" described in IEC 62232:2022, ii) guarantee a minimum EIRP level, and iii) prevent resource shortages at all times. We first investigate exact and conservative algorithms, with linear and constant complexity, respectively, to compute the maximum allowed EIRP consumption under constraints i) and ii), referred to as EIRP “budget”. Subsequently, we design a control method based on Drift-Plus-Penalty theory that preemptively curbs EIRP consumption only when needed to avoid future resource shortages.