12 December 2023 in IEEE Access
Base stations equipped with large multi-antenna systems and associated beamforming schemes provide large capacity and coverage. Massive multiple-input-multiple-output (MIMO) with beamforming was introduced as one of the enablers of 5G system performance, and this technology is evolving with the introduction of more advanced algorithms for spatial multiplexing. One of the most relevant conditions to support deployment of 5G base stations with massive MIMO is to assess realistic RF electromagnetic field exposure compliance distances leveraging the actual maximum approach introduced in IEC 62232:2022. This evaluation method takes into account the variability of traffic load and beam patterns used by the beamforming algorithm. This work investigates the impact of various beamforming schemes, like grid-of-beams, eigen-beamforming and zero-forcing, as well as various array antenna configurations on the evaluation of the power reduction factor used when implementing the actual maximum approach for RF electromagnetic field compliance assessment of massive MIMO base stations. The modelling results show that lower power reduction factors can be considered for eigen-beamforming and zero-forcing beamforming algorithms compared to grid-of-beam. The power reduction factor drop can be up to -4 dB when 8 user equipment’s are connected simultaneously.
19 November 2020 in IEEE Access
The 5th generation of mobile communication system (5G) enables the use of millimeter wave frequency bands and beamforming with narrow-beam directional antennas for mobile communication. Accurate estimation of radio link budget which enables direct assessment of achievable cell range or maximum throughput and facilitates network parametrization before deployment is one of the most challenging problems in radio network planning. In contrast to traditional cellular systems, where omni-directional or sectoral antennas are deployed with half-power beam-width much larger than angular spread of the radio channel, the beam-width of antenna arrays assumed for 5G in sub-6GHz and millimeter wave bands can be comparable to or smaller than channel angular spread in scattering environment. Since the effective antenna pattern is determined jointly by the nominal antenna pattern and channel angular spread, it is no longer appropriate to use nominal pattern in radio link budget analysis or system level simulations. Simplified approach, where nominal pattern is assumed for all typical propagation conditions, results in overestimation of the signal power in serving links and underestimation of interference, which in consequence gives erroneous estimation of link budget and leads to unsatisfactory network design and deployment. To avoid inaccurate calculation of link budget while maintaining simplicity it is proposed to modify the simplified approach by using effective antenna patterns. On the other hand, effective antenna pattern can be further optimized by matching its half-power beam-width to the angular spread of the radio channel. It is demonstrated via simulations how to rework the radio link budget for accurate estimation of system performance in high bands for 5G and beyond, along with benefits of effective antenna pattern optimization.
12 January 2022 in IEEE Access
The International Electrotechnical Commission (IEC) develops and validates methods for assessing radio frequency electromagnetic field (RF EMF) exposure due to base stations (BS). When the assessment is performed in- situ, it is recommended to extrapolate the maximum level of exposure from measurement of stable signals, such as broadcast signal with BS of the 5 th generation (5G) of mobile communication systems (gNodeB). A comparative statistical analysis of extrapolation methods based on nominal antenna pattern (as measured in an anechoic chamber) and effective antenna pattern (as measured in scattering environment) of gNodeB is presented in this paper. This theoretical analysis shows that extrapolation with nominal antenna pattern may lead to significant overestimation of the maximum RF EMF exposure (up to 5.4 dB) in case of scattering environment or non-line-of-sight (NLOS) conditions. This overestimation is expected to be reduced by using effective antenna pattern in order to better represent the actual propagation conditions, such as those found in urban or dense urban areas. Therefore, it is recommended to perform extrapolation of the maximum exposure based on joint modeling of antenna beam pattern and representative value of the angular spread (AS) for the targeted deployment conditions. This conclusion was obtained from the observed consistence between two different approaches for determination of effective antenna gain. The first approach assumes statistical simulations with full three-dimensional (3D) channel model, especially distribution function of AS. The second approach enables simpler calculation of the effective antenna gain in scattering environment or NLOS conditions by considering only representative values from the full range of AS distribution function. The proposed simple method, if used with representative realistic values of AS, could reduce overestimation of RF EMF exposure resulting from an extrapolation factor based on nominal antenna gains of broadcast and traffic beams.
12 January 2024 in IEEE Access
The development of wireless systems technologies consists, on the one hand, in new methods of generating a radio signal and, on the other hand, in optimizing the transmission of this signal, for instance, by using modern multiantenna technology. This is particularly visible in cellular systems, especially 5G, where network capacity, link throughput and energy optimization are very important. Changes in technology are followed by the need to adapt methods for measuring the electromagnetic field strength in the vicinity of the base station to new cellular standards, mainly because of the introduction of features that allow for real time change in radiation pattern and power distribution. This paper presents basics of multiantenna systems and beamforming techniques for modern cellular networks and the related consequences of evaluating electromagnetic field distribution in the vicinity of such installations for the purpose of compliance with the applicable radio frequency exposure limits. Measurement methods are presented together with the proposal for the optimized and simplified methodology, which can be used for the in-situ electromagnetic field exposure assessment in the vicinity of base stations with multiantenna systems and the configured maximum transmitted power. The measurement methodology has been verified empirically.
25 September 2024 in IEEE Access
When performing a radio frequency (RF) electromagnetic field (EMF) exposure assessment of a base station as described in the international standard IEC 62232, the actual maximum approach provides an assessment method based on the actual exposure level, in particular for massive MIMO base stations. Computational modeling can be used to estimate a range of applicable power reduction factors. To date, research studies have generally focused on the channel modeling of actual RF EMF exposure assuming that the attached user equipment (UE) is static. However, in real operational conditions, a UE can be moving and triggering multiple beam changes or beam adaptations. This study provides a computational model applicable to moving UEs and investigates the impact on range of applicable power reduction factors compared to modelling studies using static UEs. The results show that -1.5 dB to -3.5 dB lower power reduction factor can be considered with moving UEs compared to static UEs.