6 June 2017 in IEEE Transactions on Power Electronics
The limited value of the insolated-gate bipolar transistors (IGBTs) blocking voltage is an important issue for applying these devices to the high-voltage power converters. An effective solution is to use a series configuration of these devices in order to achieve higher voltage ratings in addition to save the interesting features such as fast rising time. To reach this goal, acceptable equal voltage sharing for the IGBTs are provided by the series stacking schemes in the normal operation. However, a considerable difference in their voltage level will be occurred in the short-circuit condition. Although the IGBT can withstand the short-circuit current in a defined time, the occurred high voltage stress for the IGBT is fatal in such condition. To solve the mentioned problem, this paper proposes a short-circuit protection system suitable for the series stacked IGBTs. Using this proposal, the safe voltage level for IGBTs as well as the adequate time for the performance of the detection and elimination of the short-circuit fault will be provided. Each IGBT can have a different short-circuit current in the active region since the proposed scheme makes the IGBTs independent in terms of the current in the series structure. An external resistor added to the IGBTs emitter improves the equality of the IGBTs short-circuit currents and consequently their voltage sharing. This resistor controls the system short-circuit current by changing the operating point of IGBTs in active region in the short-circuit fault. The experimental and simulation results show that the safe condition is provided for the IGBTs under the short-circuit fault.
9 June 2016 in IEEE Transactions on Plasma Science
The series configuration of fast semiconductor switches seems to be the key component in the high-voltage and fast rising time pulse generation. In this approach, two important issues must be considered. The first is to provide a safe operating condition for the switches in transient intervals. The second is to design a gate drive system with the capability of driving a large number of discrete devices simultaneously. The aim of this paper is to obviate these two requirements. First, different factors affecting the unbalanced voltage sharing between the series switches are discussed. In this investigation, the switch-to-ground parasitic capacitance effect has been recognized as the major effect on the unbalanced voltage sharing in the transient interval. Two schemes for abating this effect are proposed. To solve the unbalanced voltage distribution, the structure with a snubber circuit in the clamp mode operation is suggested. This scheme can be used for any number of switches without destructively affecting their behavior. In addition, the output pulse with a fast rising time could be obtained by the proposed gate drive system. In order to evaluate the operation of the proposed structure, a stacked switch with the voltage capability of 36 kV is tested experimentally. The characteristics of the obtained pulse are the fast rising time (69.5 ns) with the dV/dt of 460 kv/μs and the wide range of the pulsewidth adjusting to 0.5-15 μs. In addition, the voltage variance of the switches level in the series structure is about 10%.
23 January 2019 in IEEE Transactions on Power Electronics
Clamp mode snubbers are very well suited for the series structure of the insulated-gate bipolar transistors (IGBTs) in pulsed power applications. They properly meet the necessities expected from them such as the fast operating of the series IGBTs since they have no effect on the gate side. In addition, they can provide safe voltage condition for the IGBTs in short circuit faults, which are very probable in pulsed applications. The clamp mode snubber can perform its voltage balancing task whenever the power capacity of the snubber can support the injected powers due to the voltage unbalancing factors. This paper initially introduces the main factors injecting power to the snubbers. Then, it will be illustrated that the exact injected power to each predetermined snubber cannot be determined due to uncertainties about the effect of the voltage unbalancing factors. Although it is impossible to determine the exact value of the power injected to each snubber, the total injected powers to the snubbers can be calculated. Therefore, as an effective remedy, the paper proposes a concentrated snubber. Using the proposal, all the injected powers are conducted to a centralized circuit and can be easily managed. In addition, analytical expressions are provided for proper dimensioning of the proposed concentrated snubber elements. Furthermore, the performance of the proposed concentrated snubber is evaluated using simulations and experimental prototyping.
31 March 2017 in IEEE Transactions on Plasma Science
The amount of stored energy is an important issue in the low-droop and high-precision pulse generation. Pulse forming network (PFN) simulating an open-ended transmission line seems to be useful due to its minimum stored energy. The drawbacks of the PFN include low-output pulse quality and constant pulsewidth, which limit their applications. Another limitation of generating rectangular pulses using PFN is that half of the charged voltage appears in the output when delivering the entire stored energy to the matched load. This paper proposes a structure of PFN-based pulse generator that overcomes the above-mentioned limitations. For continuous pulsewidth adjustment, a lossless scheme is presented. By increasing the ratio of the load magnitude to the characteristic impedance, the amplitude of the output pulse voltage would be approximately equal to that of the charged voltage. Therefore, the semiconductor switches can be utilized in the PFN pulse generator easily. In addition, the pulse quality is enhanced and faster rising time is obtained in comparison with the conventional PFNs. In this proposal, the stored energy quantity is limited to three times the energy needed for the output pulse in the case of RL = 10Z₀. To verify the proposed structure, a prototype is simulated using PSPICE software, and the experimental results are presented.
11 June 2019 in IEEE Transactions on Industrial Electronics
Applying series configuration of the insulated gate bipolar transistors (IGBTs) to the pulsed power supplies offers unique features such as compactness and long life time. In the high voltage pulsed power supplies, a large number of the IGBTs are required to be serially connected. Hence, the safe operating condition provision for the series IGBTs is an important and crucial issue. The effect of the voltage unbalancing factors becomes remarkable when the switches number in the series structure increases. There are passive and active methods to balance the voltage of the series IGBTs. In both of these methods, an amount of power must be dissipated to remove the effect of the voltage unbalancing factors. Consequently, the power loss is considerable when a large number of series devices are necessary. This paper proposes an effective power recovery system that recovers the power associated with the series stacking of the IGBTs. Using this proposal, the efficiency of the resulted series switch enhances considerably. The power recovery system can be implemented easily for any number of series IGBTs. It consists of a simple DC/DC converter and several interconnection diodes for power recovery procedure. Proper performance of the proposed structure is evaluated by the aid of simulations and experiments.
14 January 2020 in IEEE Transactions on Power Electronics
This paper describes the development of an 18 kV, 30 kW power supply for a pulsed current load with the maximum current of 20 A and a di/dt equal to $100 \text{A}/\mu s$ . The achieved output ripple is less than 0.01%. In such a high level of precision, the most important issues are: 1) A considerable difference between the instantaneous and average output powers, as well as insufficient reaction speed of the converter to the fast load change. 2) Very low level of the voltage feedback and its sensitivity to the noise. The first issue necessitates a notable overdesign of the converter switches if the output voltage precision is dedicated to the converter. The second issue raises the problems relevant to observing the voltage ripple and providing it for the control loop. This paper proposes, a fast and high current linear regulator developed based on the load current feedforwarding. Using this approach, the fast regulator compensates the voltage change caused by a high level of instantaneous power. The main converter maintains the average power. Thus, there is not any need for the converter overdesigning. Furthermore, the problems relevant to the high voltage feedback and providing it for the control loop are removed. The voltage feedback is solely served to correct the current loop probable error. Hence the sensitivity of the control loop against the existing noise is minimized. Despite existing a 600nF capacitor as the output capacitor, the output voltage drop is less than 0.01 % in a wide range of the output current pulse up to $250 \mu s$ . The power supply is constructed and experimental results are provided to verify the mentioned specifications.