Clamp mode snubbers are very well suited for the series structure of the insulated-gate bipolar transistors (IGBTs) in pulsed power applications. They properly meet the necessities expected from them such as the fast operating of the series IGBTs since they have no effect on the gate side. In addition, they can provide safe voltage condition for the IGBTs in short circuit faults, which are very probable in pulsed applications. The clamp mode snubber can perform its voltage balancing task whenever the power capacity of the snubber can support the injected powers due to the voltage unbalancing factors. This paper initially introduces the main factors injecting power to the snubbers. Then, it will be illustrated that the exact injected power to each predetermined snubber cannot be determined due to uncertainties about the effect of the voltage unbalancing factors. Although it is impossible to determine the exact value of the power injected to each snubber, the total injected powers to the snubbers can be calculated. Therefore, as an effective remedy, the paper proposes a concentrated snubber. Using the proposal, all the injected powers are conducted to a centralized circuit and can be easily managed. In addition, analytical expressions are provided for proper dimensioning of the proposed concentrated snubber elements. Furthermore, the performance of the proposed concentrated snubber is evaluated using simulations and experimental prototyping.
11 August 2022 in IEEE Transactions on Power Electronics
Gate oxide degradation, which considerably affects turn- on /- off dynamics of the switch, embraces a large percentage of chip-related failure modes both in silicon and silicon carbide power MOSFETs. The gate oxide layer is thinner in silicon carbide power MOSFETs in comparison to their silicon-based counterparts. Consequently, the problem of gate oxide degradation has become a more crucial impediment in achieving reliable performance in silicon carbide power MOSFETs. This problem is even more severe in high-frequency applications due to higher EMI signature and complicated and costly measurement. In this article, a reliable fully analog cost-effective gate oxide degradation condition monitoring technique is proposed and validated. High-order harmonics magnitudes of drain–source voltage are used to produce a dc signal as the aging precursor of the gate oxide region. Using a dedicated degradation setup, the credibility of the developed condition monitoring technique was examined at different rates of gate oxide degradation for 650-V/22-A silicon carbide discrete MOSFET. In 200-kHz, 217-V switch operation, the proposed precursor showed 68% change in comparison to its initial value. This brings a high-resolution assessment on the reliability level of the switch gate oxide region.
5 October 2022 in IEEE Transactions on Industrial Electronics
The reliability of power converters is one of the important issues due to the widespread applications of power electronics in many industrial fields. Accordingly, condition monitoring (CM) methods for the assessment of the health of the converter components are considered a practical topic for researchers and experts in the field. This article aims to propose a CM method for insulated gate bipolar transistor (IGBT) gate oxide degradation. The proposed CM is based on the gate–emitter current during the turning- on process. It is shown that in the degradation process, the gate current peak value majorly increases. The proposed CM method captures this peak value and uses it as a degradation indicator. The proposed method is simple and analogous and can be used easily for online health assessment of the IGBTs under operation. It can be integrated into the driver module to assess the gate oxide degradation of the device. The functionality of the proposed method is evaluated using experimental prototyping. The target devices are a 1200-V, 40-A trench-gate field-stop IGBT and a 600-V and 60-A planner gate punch-through discrete IGBT. The achieved results show the validity and acceptable performance of the proposed CM for detecting the gate oxide degradation of the device.
11 June 2019 in IEEE Transactions on Industrial Electronics
Applying series configuration of the insulated gate bipolar transistors (IGBTs) to the pulsed power supplies offers unique features such as compactness and long life time. In the high voltage pulsed power supplies, a large number of the IGBTs are required to be serially connected. Hence, the safe operating condition provision for the series IGBTs is an important and crucial issue. The effect of the voltage unbalancing factors becomes remarkable when the switches number in the series structure increases. There are passive and active methods to balance the voltage of the series IGBTs. In both of these methods, an amount of power must be dissipated to remove the effect of the voltage unbalancing factors. Consequently, the power loss is considerable when a large number of series devices are necessary. This paper proposes an effective power recovery system that recovers the power associated with the series stacking of the IGBTs. Using this proposal, the efficiency of the resulted series switch enhances considerably. The power recovery system can be implemented easily for any number of series IGBTs. It consists of a simple DC/DC converter and several interconnection diodes for power recovery procedure. Proper performance of the proposed structure is evaluated by the aid of simulations and experiments.
14 January 2020 in IEEE Transactions on Power Electronics
This paper describes the development of an 18 kV, 30 kW power supply for a pulsed current load with the maximum current of 20 A and a di/dt equal to $100 \text{A}/\mu s$ . The achieved output ripple is less than 0.01%. In such a high level of precision, the most important issues are: 1) A considerable difference between the instantaneous and average output powers, as well as insufficient reaction speed of the converter to the fast load change. 2) Very low level of the voltage feedback and its sensitivity to the noise. The first issue necessitates a notable overdesign of the converter switches if the output voltage precision is dedicated to the converter. The second issue raises the problems relevant to observing the voltage ripple and providing it for the control loop. This paper proposes, a fast and high current linear regulator developed based on the load current feedforwarding. Using this approach, the fast regulator compensates the voltage change caused by a high level of instantaneous power. The main converter maintains the average power. Thus, there is not any need for the converter overdesigning. Furthermore, the problems relevant to the high voltage feedback and providing it for the control loop are removed. The voltage feedback is solely served to correct the current loop probable error. Hence the sensitivity of the control loop against the existing noise is minimized. Despite existing a 600nF capacitor as the output capacitor, the output voltage drop is less than 0.01 % in a wide range of the output current pulse up to $250 \mu s$ . The power supply is constructed and experimental results are provided to verify the mentioned specifications.
21 July 2020 in IEEE Transactions on Industrial Electronics
This article proposes a high-voltage fault current limiter (HVFCL) for high-voltage dc power supplies (HVdcPSs) which limits the current of the power supply automatically in the short-circuit fault (SCF). The proposed HVFCL is based on the series-connected insulated gate bipolar transistors (IGBTs). The main achievements of this article are the balanced voltage sharing and a very low value of the short-circuit current near to the load nominal current for the series-connected IGBTs during the SCF. These achievements result in a longer maximum permissible short-circuit time. These achievements are obtained by a control strategy that puts the series-connected IGBTs in a specific operating point in the active region during the SCF. Based on the proposed master–slave control strategy, one of the IGBTs is current controlled and rolls as the master. The other IGBTs are voltage controlled and imitate the master IGBT voltage. Consequently, a balanced voltage sharing is guaranteed for the series-connected IGBTs in the SCF. PSPICE simulations and experimental results are provided to verify the proper performance of the proposed HVFCL.