17 September 2020 in IEEE Transactions on Instrumentation and Measurement
Antenna-in-package (AiP) technology has been a main design scheme of millimeter-wave (mmWave) phased array antennas for 5G communications. The beamforming pattern of mmWave phased array AiP is steered by controlling the amplitude and phase excitations of AiP elements. It would be helpful to evaluate the control accuracy of complex excitations and to reliably calibrate mmWave AiP. However, these tasks are not trivial and time-consuming in practice, especially when the number of AiP elements is large. To address this problem, this paper presents an efficient and automated mmWave phased array experimental platform. To reduce measurement time, a control software is developed to automatically control the AiP and measurement instruments simultaneously. This experimental platform has flexible gain and phase control of AiP element excitations, and customized measurements in an automated and efficient way can be realized. The effectiveness of the experimental platform is demonstrated by several measurement campaigns, where control accuracy, array calibration, and beam steering for mmWave phased array AiP are extensively investigated.
1 February 2020 in AEU - International Journal of Electronics and Communications
25 January 2021 in IEEE Transactions on Instrumentation and Measurement
Antenna-in-package (AiP) technology has been implemented for millimeter-wave (mmWave) phased array design with antenna elements and radio frequency (RF) chips integrated. The radiation pattern beam of mmWave phased array AiP is typically steered after the in-homogeneous RF branches are aligned (i.e., AiP calibration). The RF branch discrepancies among elements are directly obtained with one element enabled sequentially each time (i.e., on-off mode) by default in the industry. A recent study has reported that the AiP element branch discrepancies obtained in the on-off mode might be different from those obtained in the normal all-on working mode with all elements active. However, experimental results that demonstrate the impact of the difference between the two calibration modes on the beam-steering performance of mmWave phased array AiP have been rarely reported in the literature. In this article, the beam-steering performance of two mmWave AiPs after the two calibration modes is experimentally compared, which is demonstrated by the beam-steering pattern defined in this article. Following the statement on the source of difference between the two calibration modes of AiP, the system model is described for the calibration and beam-steering measurements of AiP in the experimental campaign. Experimental results show that the on-off calibration mode obtains the same beam-steering performance as the all-on mode for the main beam pattern, though element branch discrepancies obtained in the two modes are different.
25 July 2019 in IEEE Access
Massive multiple-input-multiple-output (MIMO) is known as a large-scale antenna technology and has been enabled for the fifth generation (5G) mobile communication systems. The over-the-air (OTA) testing of massive MIMO antenna system has attracted a lot of attention in terms of evaluating the radio performance of a 5G base station (BS). As a promising OTA test methodology, the sectored multi-probe anechoic chamber (MPAC) setup is employed for the performance testing of massive MIMO BS. However, the system cost and installation are still an issue to be considered in practice (e.g., the anechoic chamber and multiple probes), though it can accurately reconstruct the flexible propagation channels by channel emulation methods. This paper proposes a virtual OTA test framework for the performance testing of massive MIMO BS on the basis of MPAC setups. As an alternative, the proposed virtual OTA test system adopting the concept of virtual probes solves the inconveniences and limitations of the actual probe installation in MPAC setups. The BS array responses to the actual probes of MPAC setups are generated in a phase matrix for the virtual probes. First, in this paper, the system description of virtual OTA testing is given. Then, the emulation method of spatial clusters is presented for the virtual OTA testing. Finally, simulations are performed with good channel emulation accuracy.
11 May 2023 in IEEE Transactions on Instrumentation and Measurement
To ensure millimeter-wave (mmWave) radio system performance, multiple beam-steered radiation patterns of phased arrays are required to be measured in conventional antenna measurement ranges. This is typically done by sequentially measuring the radiation pattern of phased array under test (AUT) with the AUT mechanically rotating in a far-field setup for each steered beam in a beam-lock mode. However, the conventional pattern measurement procedure for mmWave phased arrays with multiple beams is time-consuming and costly due to the repetitive mechanical rotation and the use of far-field anechoic chamber. The problem becomes even more pronounced for mmWave phased arrays with large-scale antenna configuration due to many more beam states and more directive beam patterns. To address this issue, this paper proposes a novel near-field multi-beam measurement system for mmWave phased arrays, which offers unique advantages in terms of short measurement time, support for full automation, no need for mechanical rotation, compact measurement setup and low system cost. For the pattern with its beam steered to any given direction can be reconstructed based on the AUT element patterns retrieved from a few sparse measurement samples. In this work, the principle and effectiveness of the proposed measurement system have been firstly validated by electromagnetic simulations with CST Studio Suite. Besides, a practical system prototype has been built and experimentally validated where the near-field reconstructed multi-beam patterns are shown to match well with the far-field target patterns in terms of beam direction, beam gain, and pattern similarity percentage.
11 May 2022 in IEEE Antennas and Wireless Propagation Letters
Accurate knowledge of multibeam radiation patterns of millimeter-wave (mmWave) phased arrays is a key to mmWave radio system performance. The multibeam radiation patterns can be measured by conventional antenna test ranges in a sequential manner. However, these tasks can be time-consuming and low efficient in practice, especially for large-scale arrays with many beam-steering states. To address this problem, this letter proposes a multibeam reconstruction method, which can measure all possible steered beams in a fast and efficient manner. In the proposed method, multiple beam patterns are reconstructed synchronously by a fast element pattern retrieving method based on a few sparse measurement samples, which were obtained in a multiprobe setup or with the help of a turntable in a single probe setup. The proposed method is experimentally validated in a compact antenna testing range (CATR) setup at 28 GHz for a $4\times 4$ mmWave phased array with an integrated antenna-in-package design. The experimental results show that the reconstructed array multibeam patterns by the proposed method are comparable to the conventional CATR measurement results but in a faster way, which validates the effectiveness of the proposed method.