5 October 2017 in IEEE Transactions on Antennas and Propagation
SSSrijittra Swaisaenyakorn
Accurate and precise motion tracking of limbs and human subjects has technological importance in various healthcare applications. The use of impulse radio-ultra wideband technology (IR-UWB) technology due its inherent properties is of recent interest for high-accuracy localization. This paper presents experimental investigations and analysis of indoor human body localization and tracking of limb movements in 3-D based on IR-UWB technology using compact and cost-effective body-worn antennas. The body-centric wireless channel characterization has been analyzed in detail using parameters such as path loss magnitude, number of multipath components, rms delay spread, signal amplitude, and Kurtosis with the main focus to differentiate between line-of-sight (LOS) and non-LOS situations. Fidelity of the received signal is also calculated for different activities and antenna positions to study the pulse preserving nature of the UWB antenna, when it is placed on the human body. The results reported in this paper have high localization accuracy with 90% in the range from 0.5 to 2.5 cm using simple and cost-effective techniques which is comparable to the results obtained by the standard optical motion capture system.
19 June 2018 in IEEE Antennas and Wireless Propagation Letters
21 January 2022 in IEEE Transactions on Communications
Reconfigurable intelligent surface (RIS) technology is promising to enhance wireless communications services by providing smart radio environment. In this paper, we investigate the RIS aided cellular networks with device-to-device (D2D) users, and maximize the sum of the transmission rate of the D2D communications and the cellular networks from a new perspective. In addition to solving the typical resource allocation problems for D2D communications, this paper further optimize the wireless environment by adjusting the position and phase shift of the RIS. To solve this non-convex problem, we propose a novel decentralized double deep Q-network (D3QN) framework for the resource allocation at users and a centralized DDQN for RIS optimization at the base station (BS), which are verified to achieve the near-optimal performance with lower complexity and enhanced robustness. Simulation results illustrate that the proposed framework can achieve higher transmission rates compared to benchmarks, meanwhile meeting the quality of service (QoS) requirements at the BS and D2D users.
16 July 2020 in IEEE Transactions on Antennas and Propagation
This paper presents a novel 3D-printed, pyramidal double-ridged horn antenna, filled with a high-dielectric material comprising a mixture of linseed oil and titanium oxide, for biomedical applications. In particular, this investigation explores the use of the antenna design to measure the abdominal fat layers of the human body. The antenna is designed to operate at the low-frequency microwave bands and complemented with an absorber layer at the aperture to improve directivity. The proposed method aims to assess the fat layer thicknesses based on an analysis of the variations of the reflection coefficients. The system has been calibrated and validated based on a number of numerical time-domain simulations, as well as experimental analysis. Assessment of the first transition point in the reflection coefficient spectrum, has successfully predicted the rate of magnitude change caused by different layer thicknesses (e.g., oil and fat). Comparing coefficient spectra from various simulation experiments has allowed for eliminating the interferences arising from mismatches with the skin and muscle layers, resulting in the measurements of the fat layer thicknesses through the remaining power change rate.
6 February 2020 in IEEE Access
A design criterion for a compact 3D printed high gain corrugated plate antenns that has high aperture efficiency and wide bandwidth is presented in this paper. The proposed design criterion is validated numerically and experimentally by fabricating 3D printed and Aluminium prototypes for X-band and Ka-band applications. The proposed antenna structure consists of two layers, where the electromagnetic energy (EM) is launched into a cavity that exists between both layers and the EM energy is coupled to the surface of the second layer. The second layer is the radiating structure which consists of three slots surrounded by a rectangular cavity and periodic corrugations that significantly improve the gain of the antennas. The 3D printed prototypes of the proposed antennas are fabricated and tested to validate the proposed design criterion, and their performance is compared to the Aluminium metallic counterparts. Using 3D printing technology, to fabricate the proposed antennas offer low cost and low weight alternatives to the Aluminium metallic prototypes. The measured results of the fabricated prototypes show high gain, high aperture efficiency, low side lobe level, and low cross polarization performance over a wide bandwidth.
24 June 2022 in IEEE Transactions on Antennas and Propagation
Compressive sensing (CS) has been deployed in a variety of fields including wideband spectrum sensing, active user detection, and antenna arrays. In massive multiple input multiple output (MIMO) arrays, CS has been applied to reduce the number of measurements required to verify the arrays excitation. To date, the literature has concentrated on the various methods of achieving CS and applying them to both linear and 2-D arrays, and aimed at detecting fully failed elements in an array, offering simple pass/fail testing. All follow the general approach of creating the sparsity needed for CS by subtracting the measured far field or near field of the test array from that of a “gold standard” array measured under exactly identical conditions. This article extended this work to the need for rapid but accurate reconstruction of element excitation in a production testing environment for massive MIMO arrays. The aim is to demonstrate that CS can offer accurate reconstruction of array excitation. Particularly, the work addresses the issues of optimal sampling, measurement noise, accuracy of faulty element detection, effects of beam scanning, and physical alignment of the gold standard array with the test array. We have restricted ourselves to considering production standard arrays with failure rates up to around 5% and conclude with a set of proposed modifications to the basic CS process as applied to array excitations that achieve a near 20 dB improvement in the accuracy of the reconstructed array excitation offering mean square errors (MSEs) near to −40 dB, with a sampling strategy of just 1.4% of the Nyquist rate. This is achieved with the number of measurements to array element size ratio of approximately 0.2.