Currently, the interest and the need to innovate new materials through the use of waste materials has grown, which meet similar or improved physical, chemical and mechanical characteristics of the materials they will replace. During the present investigation, Multilayer Containers (EM) and Low Density Polyethylene (LDPE) were collected, particulate agglomerates with different proportions were obtained, the apparent density, water absorption, mass, volume, heat behavior, angle were determined. contact, machining and compression tests. With the objective of evaluating the proportions p / p in the properties. The advantage of the material obtained is that they do not generate waste and are 100% recyclable. The 90:10 ratio is the one that could be used in the construction industry as false walls, with a modulus of rupture of 52.7 N / mm2 and a compressive stress of 32.9 MP, because it can be machined without altering its characteristics. -physical houses; While the 85:15 and 80:20 proportions, since they cannot be machined, could be used as a floating support with a photocatalyst catalyst, due to the fact that these agglomerates have dimensional stability when in contact with water.
30 September 2019 in Revista de Ingeniería Eléctrica
In this work, a temperature control system (SCT) was designed and implemented in the thermoforming process for the manufacture of blocks for wall construction (BCM). The control process in the SCT consists in establishing the reference temperature for the thermoforming and send it to the Mega 2560 microcontroller. This component processes the input signal, obtaining six digital signals that control the surface temperature of each of the external faces of the BCM mold that has a rectangular prism geometry. These signals are sent to the electrical isolation stage where the actuators enable six electrical resistances (200 Watts to 120 Volts). The feedback of the temperature in the control system was made through type-k thermocouples, whose analog signals are compared with the reference signal to regulate the temperature. This project contributes to establish and control the temperature of the resistances, implemented for the thermoforming process, for the elaboration of blocks using multilayer containers.
30 September 2019 in Revista de Energía Química y Física
Floating photocatalysts have caused interest due to the benefits they provide. For example, the floating support has characteristic lightness and flexibility; while the photocatalyst has the advantage of being able to interact with sunlight without the need of stirring or oxygenation. In this paper, a floating photocatalyst based on a TiO2/ agglomerate composite is evaluated. The agglomerate is made from post-consumer packaging of multilayer containers. The catalyst was prepared by synthesizing of titanium dioxide powders with phase mixture anatase/rutile. The photocatalyst powder was attached to substrate surface using a varnish obtained by dissolving post-consumer polystyrene containers in toluene. The photocatalyst has different phase A-R (Anatase-Rutile) ratios. The approximate size of the nanostructure is 13.29 ± 3.28 nm, calculated using UV-Vis spectroscopy, the bandgap has values ranging from 2.56 eV to 2.90 Ev. The agglomerates have a rupture modulus of 14.95 N/mm2; they are hydrophobic materials and possess dimensional stability against changes in humidity (length) less than 10%, chemical resistance, are flame retardant. The TiO2/agglomerate composite is used for the photocatalytic degradation of a model pollutant (methylene blue) using sunlight.
31 December 2024 in Revista de la Invención Técnica
In this work, the synthesis of a composite material based on hydroxyapatite (HAp) and zinc oxide (ZnO) is reported. Two types of synthesis were evaluated, in order to know which of them allows to obtain a homogeneous composite material of HAp and ZnO, since making a composite material implies that two or more compounds must be integrated and do not separated; the HAp will be obtained from eggshell residue, ZnO will be synthesized by Sol-Gel and electrolysis; in the ZnO obtention, the previously synthesized HAp was incorporated and it is followed by a thermal treatment obtain the oxide. To evaluated the incorporation of ZnO with hydroxyapatite, Scanning Electron Microscopy, Elemental Analysis and Mapping by Energy Dispersive Spectrometry, Infrared Spectroscopy Analysis and X-ray Diffraction were performed. These two synthesis methods are aiming to obtain a homogeneous material, establishing a methodology to produce the material composite, as well as improve the photocatalytic properties.
El presente trabajo se enfocó en el estudio del vidrio reciclado como refuerzo en losetas de cemento, con el objetivo de evaluar su influencia en las propiedades mecánicas y explorar su viabilidad en la industria de la construcción. Para ello, se fabricaron 4 lotes de losetas por triplicado variando la proporción p/p de vidrio y cemento, L1 es el blanco (proporción 0:1), el tamaño de partícula vario: L2 con 354 µm (proporción 1:4), L3 de 250 µm (proporción 1:5) y L4 con 105 µm (proporción 1:5). Se realizaron ensayos mecánicos a los 7, 14 y 28 días de curado, siguiendo la norma ISO 10545-4:2019(E). Además, se utilizó un esclerómetro para evaluar la resistencia superficial de las probetas según la norma NMX-C-192-ONNCCE-2018. Los resultados mostraron que, aunque la incorporación de vidrio permitió obtener una matriz más homogénea y estética, la resistencia mecánica de las losetas fue inferior a la de losetas comerciales con tratamiento térmico. La mezcla con partículas de 250 µm (L3) presentó una mayor resistencia a la flexión, alcanzando 0.25 MPa, mientras que la resistencia a la compresión en los cilindros superó los 40 MPa en las probetas L2 y L3 a los 28 días, siguiendo la norma NMX-C-111-ONNCCE-2018. Este estudio evidencia el potencial del vidrio reciclado en la fabricación de losetas, aunque se requieren optimizaciones en la formulación para mejorar su desempeño estructural
Currently, new materials are being developed to remove contaminants from wastewater by combining materials to improve their individual properties. This chapter describes the production of the zinc oxide (ZnO) and carbon composite. The ZnO was synthesized by electrolysis, adding Spend Coffee Grounds (SCG) to the electrolytic medium, and finally calcined at 400 °C for 30 min. ZnO, carbon, and the composite were synthesized and characterized. Scanning Electron Microscopy found that ZnO deposits in the pores of the carbon; Infrared Spectroscopy identified bonds associated with carbon and ZnO; X Ray Diffraction yielded a diffractogram with lower intensity compared to that of ZnO (JPDS-361451), due to the synthesis of amorphous carbon; μ-RAMAN Spectroscopy detected characteristic bonds of both materials; finally, the isoelectric point of the composite is 7.3, which will allows working with sorption in neutral systems.