Niklas Eyckeler

Niklas Eyckeler

Auto-generated profile, based on publicly available information

Niklas Eyckeler

Inst. of Energy and Climate Research, Forschungszentrum Jülich GmbH

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2023 in ECS Transactions
Verified
Journal Article
Closed access
Stephanie Elisabeth WolfStephanie Elisabeth Wolf
Stephanie Elisabeth Wolf
Vaibhav VibhuVaibhav Vibhu
Vaibhav Vibhu
CCCarla L. Coll
Carla L. Coll
NENiklas Eyckeler
Niklas Eyckeler
IVIzaak Vinke
Izaak Vinke
LHL.G.J. de Haart
L.G.J. de Haart
Severe performance loss of state-of-the-art Ni-cermet fuel electrodes has been observed due to Ni particle agglomeration and Ni migration away from the triple-phase boundary at the active electrode layer. Investigation of Ni-free perovskite Sr2Fe2-xMoxO6-δ (SFM)–30 wt% Ce0.8Gd0.2O2-δ (GDC) as fuel electrode material showed good redox stability in oxidizing and reducing atmospheres. These characteristics meet exactly the targeted requirements for new solid oxide electrolyzer materials. A comparison of SFM and SFM-GDC fuel electrodes showed similar performance for H2O, CO2, and co-electrolysis between 750 °C and 900 °C. Long-term degradation measurements and post-test SEM-EDX analysis clarified that SFM-GDC exhibits good phase stability in comparison to pure SFM fuel electrodes. The composite fuel electrode Sr2Fe1.1Mo1.0O6-δ–30 wt% Ce0.8Gd0.2O2-δ (SFM15-GDC) reached polarization resistances (RP) in the same range as Sr2Fe1.0Mo1.0O6-δ with around 127 mΩ∙cm² and 137 mΩ∙cm at 900 °C in steam electrolysis.

14 March 2025 in Journal of Physics: Energy
Verified
Journal Article
Open access
Stephanie Elisabeth WolfStephanie Elisabeth Wolf
Stephanie Elisabeth Wolf
JUJan Uecker
Jan Uecker
NENiklas Eyckeler
Niklas Eyckeler
LSLeon Schley
Leon Schley
LHL.G.J. de Haart
L.G.J. de Haart
Rüdiger-A. EichelRüdiger-A. Eichel
Rüdiger-A. Eichel
The internal reforming of biogas, a mixture containing carbon dioxide (CO2) and methane (CH4), in solid oxide and solid proton conducting fuel cells (SOFCs, SPCFCs) is a sustainable and efficient method to produce syngas (H2 + CO) in combination with highly efficient electrical power generation. Reforming processes convert biogas into syngas by steam reforming, dry reforming, or partial oxidation, which then undergoes electrochemical reactions in the SOFCs/SPCFCs to produce electricity and heat. The dry methane reforming process of the anthropogenic greenhouse gases CH4 and CO2 into biogas can result in co-generation of electrical power and syngas mixtures of CO:H2 relevant for large-scale industrial processes like the Fischer–Tropsch process. Herein, a short review of promising developments in the literature concerning the internal dry reforming of biogas (CH4 and CO2) in oxygen-ion conducting and proton-conducting fuel cells is provided. The thermodynamics of different reforming processes, the advantages, disadvantages, and the fundamental electrochemical processes in SOFCs and SPCFCs are discussed comprehensively and comparatively. In addition, this article aims to provide a perspective on current gaps and possible future research efforts.

24 November 2025 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
NENiklas Eyckeler
Niklas Eyckeler
TFTill Frömling
Till Frömling
Rüdiger-A. EichelRüdiger-A. Eichel
Rüdiger-A. Eichel
With the global push toward a sustainable hydrogen economy, Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for efficient hydrogen production. Especially their ability to utilize both electrical and thermal energy and the absence of scarce and expensive catalyst materials is a striking advantage for their integration into renewable energy systems or industrial processes. However, their long-term degradation significantly limits their operational reliability and scalability. Building on previous fundamental studies, this work presents advancements in establishing a simulation-based framework to understand degradation mechanisms in commercial, fuel-electrode-supported Ni-YSZ SOECs. Using the commercial COMSOL Multiphysics ® software, an integrated approach is developed that combines a finite element method (FEM)-based multiphysics model with experimental data. This study paves the way for a framework bridging critical gaps in linking microstructure evolution to performance degradation. Experimental performance data derived from i-V characterization and FIB-SEM tomography serve as the basis for model validation and refinement. The developed FEM model simulates coupled physicochemical processes within the SOEC, allowing for deeper insights into the interplay between microstructural parameters and cell performance metrics. Special attention is paid to microstructural changes during degradation, with key parameters such as porosity, tortuosity, and active surface area being explicitly resolved. The model attempts to elucidate critical aspects such as diffusion limitations and the pivotal role of Triple Phase Boundaries (TPBs) in electrochemical processes. Building on prior studies that examined the model’s general ability to describe degradation processes, [1] this study focuses on refining and optimizing the simulation framework for SOEC button cells. Therefore, the aim is to develop a robust framework for the simulation of SOEC button cells, based on which targeted investigations of microstructural influences will be possible. As a first step, the model was therefore subjected to thorough benchmarking, including rigorous analysis of mesh size and granularity, as well as the fraction of the cell domain considered. Essentially, the benchmarking of the model aimed at a balance between computational efficiency and accuracy. During the benchmarking procedure curves for various predefined and custom mesh settings were compared to identify the optimal mesh resolution beyond which further mesh refinement no longer detectably influenced the results. This analysis identified a mesh configuration with element sizes ranging from 4 µm to several hundred µm, yielding average element sizes that are slightly larger but still comparable to the Ni-YSZ cermet particle sizes reported in established literature. [2-6] Further mesh refinement only led to marginally improved accuracy, and thus demonstrated particle-level resolution to be unnecessary for accurate process depiction. The developed mesh configuration allows the resolution of degradation phenomena like Ni depletion, which according to Hauch et al. [4] as well as Sciazko et al. [5] occur in the electrolyte-adjacent 5 µm region, while avoiding the exponentially increasing computational cost of ultra-fine meshes. The identified configuration thus strikes an optimal balance between computational cost and accuracy, as coarser meshes, employing maximum element sizes larger than 200 µm resulted in significant accuracy losses. On the other hand, persistent convergence challenges occur under lean feed-gas conditions when reducing the maximum element size below 190 µm. Combined with particle-level considerations being demonstrated unnecessary for accurate modeling, further mesh refinement thus offers no significant benefit. Benchmarking across varying mesh settings underscores the importance of capturing diffusion and transport processes. While high-current regimes exhibit a strong dependency on the mesh resolution, at lower current densities mesh refinement had negligible effects on simulation outcomes. Further analysis explored the impact of reducing the cell domain considered on simulation accuracy and computational time. Simulation of half-cell domains showed no differences compared to full-cell considerations within experimental accuracy, while quarter-cell domains introduced deviations that rendered such approaches impractical. This highlights the feasibility of extrapolating to a full cell using smaller domains for computational efficiency without compromising accuracy, provided that the reductions remain within optimal bounds. Studies of different gas compositions and temperature ranges during the benchmarking ensured the coverage of a wide parameter space, extending the model’s applicability beyond static operating points. This allows the exploration of different conditions from experimental procedures - demonstrating the robustness of the model to explore and decipher experimentally hardly accessible phenomena. One such phenomenon is microstructure evolution during SOEC operation. Parameter variations revealed the profound impact of microstructural features, particularly TPBs, on cell performance. These results confirm the central role of TPBs in electrochemical reactions and are consistent with established literature findings. [7] Other key parameters, such as exchange current density and active surface area, were also found to be influential in determining cell performance and degradation. The applied parameter variations demonstrated that the model is able to account for any type of loss mechanism that may occur within experiments. These results position the FEM model as a robust tool not only for understanding degradation mechanisms but also for exploring strategies to mitigate them. Despite its strengths, the model highlights areas for improvement. In particular, comparative studies between simulation and experimental data reveal an incomplete consideration of diffusion phenomena, emphasizing the need for refinements in this area. However, preliminary results suggest that the parameterization of surface areas can partially replicate diffusion limitations, providing a pathway to refined diffusion modeling. Further progress will require more detailed experimental data on real-cell microstructures to better calibrate the model. In addition, comparison of experimental and simulation data will allow identification of bottleneck reactions where further refinement of the given framework is required. References Eyckeler, M. Nohl, J. Uecker, Multiphysics modeling of degradational behavior in high-temperature electrolysis cells based on experimental studies , Master Thesis, RWTH Aachen University, Aachen, 2024 Kawashima, S. Miyoshi, Y. Shibuta, S. Yamaguchi, J. Power Sources 234 (2013), 147–153 Keane, H. Fan, M. Han, P. Singh, Int. J. Hydrogen Energy 39 (2014), 33, 18718–18726 Hauch, K. Brodersen, M. Chen, M. B. Mogensen, Solid State Ion. 293 (2016), 27–36 Sciazko, T. Shimura, Y. Komatsu, N. Shikazono, JTST 16 (2021), 1, JTST0013-JTST0013 Wang, C. Wu, B. Zu, M. Han, et al., J. Power Sources 516 (2021), 230660 B. Mogensen, M. Chen, H. L. Frandsen, C. Graves, et al., Fuel Cells 21 (2021), 5, 415–429

28 August 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
SWStephanie E. Wolf
Stephanie E. Wolf
Vaibhav VibhuVaibhav Vibhu
Vaibhav Vibhu
CCCarla L. Coll
Carla L. Coll
NENiklas Eyckeler
Niklas Eyckeler
IVIzaak Vinke
Izaak Vinke
LHL.G.J. de Haart
L.G.J. de Haart
Solid oxide electrolysis cells (SOECs) have proven to be a highly efficient key technology to produce valuable gases (H2, CO). SOECs utilize renewably generated electricity at temperatures between 600 - 900 °C, thereby providing a carbon-neutral method for energy storage. However, the successful industrial implementation of this technology requires long-term stability of all system components and is mainly delayed by the degradation of the electrodes over time. The state-of-the-art Ni-YSZ fuel electrode has been extensively studied and exhibits severe performance loss due to Ni particle agglomeration and Ni migration away from the active sites at the electrolyte/electrode interface under real operating conditions [1]. To mitigate this issue, we have investigated the Ni-free perovskite Sr2Fe2-xMoxO6-δ + 30% GDC as fuel electrode material. As mixed ionic and electronic (MIEC) perovskite structured oxides, these materials have shown excellent short-term redox stability in oxidizing and reducing atmospheres in addition to high conductivity and outstanding coking resistance [2]. These characteristics meet exactly the targeted requirements for new solid oxide electrolyzer materials. We have compared the long-term degradation of an SFM fuel electrode to an electrode made of SFM-GDC (Figure 1). The degradation was less severe for the mixed electrode of SFM-GDC. Impedance and post-test SEM-EDX analysis clarified the main degradation mechanisms of SFM as well as SFM-GDC in steam and CO2 electrolysis. The tested button cells showed demixing of the SFM phase and particle aggomeration in the fuel electrode. [1] S. E. Wolf, V. Vibhu, E. Tröster, I. C. Vinke, R.-A. Eichel and L. G. J. de Haart, Energies, 15(15), 5449 (2022). [2] L. Bernadet, C. Moncasi, M. Torrell and A. Tarancón, Int. J. Hydrog. Energy, 45(28), 14208–14217 (2020). Figure 1