13 January 2020 in IEEE Transactions on Applied Superconductivity
In this paper, an optimized method to design superconducting magnets for 14 T actively shielded MRI is proposed. At first, the feasible current-carrying region is subdivided into two-dimensional array grids, in which each grid represents one loop of a current-carrying conductor. Then the current distribution is obtained using linear programming by a detailed consideration of the superconductor consumption, central field strength, imaging region homogeneity and stray field leakage range. Afterwards the rectangular section of the magnet is obtained by reshaping the irregular current region and non-linear programming is then adopted to refine each section's position and size to obtain the final magnet configurations. In addition, the spherical harmonics elimination to the central magnetic field is proposed as the optimization strategy used in the non-linear programming method to get the least level of inhomogeneity over the imaging region and all the current centers are chosen based on the locations of actual superconducting wires of each conductor. Finally, this combined design method has obtained high field homogeneity in the central zone by four sets of coils with a total length around 3.5 m and inner diameter nearly 1 m. The detailed analysis and optimization approach will be presented.
19 May 2022 in IEEE Transactions on Applied Superconductivity
A large scale research and development project for China Fusion Engineering Test Reactor (CFETR) named the comprehensive research facility for fusion technology (CRAFT) started in 2019 and is scheduled for completion in 2025. A super-conducting conductor experiment testing platform (Super-X for short) is a sub-task of CRAFT to evaluate the future supercon-ducting part performance. The maximum testing magnetic field at bore center is 15 T, the dimensions of testing space are 100 × 160 × 550 mm, the field homogeneity of testing space is superior to 95%, and the maximum testing current is 100 kA. The direct current (DC) magnet is the key sub-system for the facility provid-ing the background magnetic field. The engineering design for DC magnet has been accomplished in the middle of this year, and its technical parameters meet the required. The main work focus-es on the structural design of the split coils, the axial preload and the hanging assembly. This paper presents the progress on the engineering design of the DC magnet.
22 June 2021 in IEEE Transactions on Applied Superconductivity
The engineering design of the China Fusion Engineering Test Reactor (CFETR) has been completed in 2020. A largescale R&D project for CFETR named the comprehensive research facility for fusion technology (CRAFT) was initiated in Sep. 2019. As a sub-task of the CRAFT, a superconducting experiment testing platform (Super-X for short) is planned to be constructed for evaluating the future superconducting parts performance. Its main technical parameter includes: the background field of 15 T, the dimensions of testing space of 100 × 160 × 550 mm, the field homogeneity of testing space ≥ 95%, and the maximum testing current of 100 kA. For now, the preliminary design for Super-X has been accomplished. The DC magnet provides the background magnetic field for Super-X. It is a kind of split coil that includes two symmetrical coils assemblies. The innermost diameter is about 644 mm, the outermost diameter is 2874 mm. Each coil assembly is composed of three concentric Nb 3 Sn coils. The peak field is 15.7 T and the field homogeneity reach to 98.2%. The high field coil (HFC) and medium field coil (MFC) is typically dominated by high-J c Nb 3 Sn cable-in-conduit conductor (CICC), and the low field coil (LFC) by ITER grade Nb 3 Sn CICC. This paper presents the preliminary design of the background DC magnet system (BM).
1 December 2020 in Review of Scientific Instruments
This paper proposes a new passive shimming method to design correction iron pieces for compensating field impurities generated by the main magnets of high field magnetic resonance imaging (MRI) for human body imaging. First, the relationship formula of a magnetic dipole to any field point in space is established. Then, a sensitivity matrix in the form of spherical harmonic expansions can be set up based on the contribution of each shim piece to each field point. Next, an optimization procedure of linear programming is applied to determine the location and thickness of the ferromagnetic shim pieces. This is different from the previous methods that consider that all magnetic moments for each magnetized iron piece are located only at its central position, which may cause some intrinsic errors. This method takes the shim piece’s volume into account and gives more accurate results in a sensitivity matrix by means of integration in the azimuthal and axial directions while the radial (thickness) direction remains constant. Finally, a case study combining the analytical method and a 3D finite element analysis simulation demonstrates that the new approach provides better results in terms of homogeneity. The method presented can also be used to design passive shims for various practical MRI applications.
30 July 2020 in IEEE Transactions on Applied Superconductivity
The conceptual design of China fusion engineering test reactor (CFETR) is now ongoing. Its toroidal field magnets with a peak field of 15 T which require a new conductor testing facility with higher background magnetic field to test and evaluate the performance of these conductors. As part of the study of CFETR, the facility named Super X (SUPERconducting eXperiment) is planning to be constructed at ASIPP and a conceptual design activity related is going on in parallel. The background magnetic field of the facility is generated by three concentric pairs of split coils with a bore of 600mm diameter, inner coil (IC, peak field of 15.6 T), middle coil (MC, 13.3 T), and outer coil (OC, 10 T) in which IC and MC are connected in series with a nominal operating current of 7.9 KA, while OC operates at 13.5 KA. Each split pair coil is made of its own distinctive rectangular shaped cable-in-conduit conductor (CICC). The design and preliminary results of electro-magnetic optimization and structural mechanical analysis for the background magnet system are presented.
1 March 2024 in IEEE Transactions on Applied Superconductivity
The Institute of Plasma Physics Chinese Academy of Sciences (ASIPP) has announced a project to design a 14 T MRI magnet with a 900 mm warm bore and comprised of Nb3Sn Rutherford cables, the homogeneity of the magnetic field is better than 0.5 ppm in a 22 cm diameter spherical volume. This paper presents three design schemes for 14 T MRI magnets based on manufacturing technology perspective, which are layered solenoid design, multicoil design and multi-coil layered design, and compares them from the aspects of mechanical design, inductance and total conductor usage to obtain the optimal scheme