In this paper, a technique for slew-rate (SR) boosting suitable for switched-capacitor circuits is proposed. The proposed technique makes use of a class-B auxiliary amplifier that generates a compensating current only when high SR is demanded by large signals. The proposed architecture employs simple circuitry to detect the need for a large output current by employing a highly sensitive pre-amplifier followed by a class-B amplifier. The functionality of the class-B transconductance amplifier is dictated by a predefined hysteresis, and operates in parallel with the main amplifier. The proposed solution demands small static power (under 20% of main amplifier power) due to its class-B nature. The experimental results in a 40-nm CMOS technology show more than 45% reduction in slew time, and a 28% shorter slew time for 1% settling time when used in a typical 4.5 bit/stage block commonly used in pipelined analog-to-digital converters. Compared with the core amplifier, HD3 at 500 MHz reduces by more than 10 dB when the SR boosting circuit is activated.
25 July 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a 12-bit 500 MS/s pipelined ADC fabricated in the 40 nm TSMC technology, which aims to reduce the power consumption associated with residue amplifiers and comparator cells. ADC architecture employs amplifiers with minimum transconductance requirements while considering the minimum unit capacitance value to maintain matching capacitor requirements for the target ADC specifications. The power efficient operational amplifiers are equipped with a Class C slew-rate boosting circuit that achieves a high slew-rate while static power is significantly saved. In addition, a forecasting technique in the sub-ADC is proposed, which reduces the number of active comparators during the sub-ADC’s conversion phase. The sign of the incoming signal is detected, and then the number of active comparators in each conversion cycle reduces by half, which leads to a more than 46% dynamic power savings from the sub-ADCs. The ADC achieves an SNDR/SFDR of 65.9/82.3 dB at low input frequencies and 64.1/75.5 dB near Nyquist frequency while running at 500 MS/s. The pipelined ADC prototype occupies an active area of 0.9 mm 2 and consumes 18.16 mW from a 1.1 V supply, resulting in a figure of merit (FOM) of 22.4 and a 27.7 fJ/conversion-step at low-frequency and Nyquist frequency, respectively.
23 August 2018 in IEEE Journal of Solid-State Circuits
A power-efficient pipeline analog-to-digital converter (ADC) architecture employing a current-mode (CM) multiplying digital-to-analog converter (MDAC) is implemented in this paper. A linear operational transconductance amplifier (OTA), a current steering DAC, and a transimpedance amplifier (TIA) work together as an error amplifier to implement the first stage of the pipeline ADC. The high output impedance displayed by both OTA and MDAC allow us to maximize the power efficiency of the residue amplifier. Compared with a conventional switched-capacitor (SC) MDAC architecture, the proposed CM MDAC reduces the architecture’s power consumption. The fabricated pipeline ADC achieves a 61.3-dB/60.2-dB signal-to-noise and distortion ratio (SNDR) and a 76-dB/74-dB spurious-free dynamic range (SFDR) for a sinusoidal input of 4.15 and 97.9 MHz, respectively. The ADC’s power consumption when operating at 200 MS/s is 8.4 mW, and the conversion figure of merit (FoM) is a 44 fJ/conversion step. The prototype occupies an active area of 0.23 mm 2 in a mainstream low-power 40-nm CMOS technology.
13 July 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper introduces a 12 bit 2.5 bit/cycle SAR-based pipeline ADC employing a self-bias gain boosting amplifier. The single-stage amplifier achieves a low-frequency gain of 37 dB, while consuming 1.3 mW of power consumption with 1.3 V of analog power supply. A 2.5 bit/cycle SAR ADC realizes as the sub-ADC in each stage, and reduces both power consumption and silicon area. A two-channel sampling architecture is employed to double the sampling rate and thereby maximize circuit efficiency. A digital calibration technique is used to reduce non-linearity and mismatches due to the RDAC, as well as gain error and offset of the open-loop residue amplifier. The prototype ADC was fabricated in TSMC 40-nm technology, and consumes 10.71 mW with 1.1 V / 1.3 V digital / analog power supplies. When operating at 125 MS/s, the ADC achieves an SFDR of 66.59 dB before calibration and 80.3 dB after calibration when measured at Nyquist frequency. The experimental results show a Walden FoM of 101 fJ/c.-s. before calibration and 47 fJ/c.-s. after calibration.
9 August 2019 in IEEE Transactions on Power Electronics
This article presents an agile supply modulator with optimal transient performance that includes improvement in rise time, overshoot and settling time for the envelope tracking supply in linear power amplifiers. For this purpose, we propose an on-demand current source module: the bang-bang transient performance enhancer (BBTPE). Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further helps the proposed system to reduce both overshoot and settling time. This article also introduces an efficient selective tracking of envelope signal for linear PAs. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in adjacent channel power ratio (ACPR) and error vector magnitude (EVM), respectively.
This paper deals with the design of power efficient switching regulators intended for linear power amplifiers employing envelope tracking techniques in wideband wireless standards. The bottlenecks in existing envelope tracking solutions involve a tradeoff between ripple voltage, slew rate and bandwidth. The slew rate limitation is identified as the main challenge and a `bang-bang' slew-enhancement technique is proposed for overcoming it. This approach enables the use of efficient supply modulators in wideband power amplifiers. The proposed scheme does not significantly degrade PA efficiency and improves the stability of the switching regulator. The prototype has been implemented using the TSMC 0.18 μm technology; schematic simulation results in Cadence ® demonstrate the feasibility of the proposed technique.