25 December 2017 in IEEE Transactions on Circuits and Systems I: Regular Papers
Linearity testing of analog-to-digital converters (ADCs) is very challenging and expensive due to the stringent linearity requirement on the stimulus and the extremely long test time. This paper introduces a novel method for ADC static linearity testing, allowing the stimulus linearity requirement to be significantly relaxed and the test time to be significantly reduced compared to the state-of-art histogram method. Two nonlinear but functionally related input signals are used as the ADC's excitation and a stimulus error removal technique is used to recover test accuracy. With a segmented non-parametric integral nonlinearity model, this method requires much fewer parameters to accurately represent the nonlinearity. The proposed algorithm has been extensively verified and correlated in simulations. This method not only enables low-cost production testing but can also be used for low-cost on-chip built-in self-test. This method is limited to ADCs with segmented architecture such as SAR ADCs, pipeline ADCs, and cyclic ADCs.
16 November 2017 in IEEE Transactions on Instrumentation and Measurement
Data converters are among the most widely used components in modern integrated devices and systems. A major challenge is to characterize their performances accurately and cost effectively. The analog-to-digital converter (ADC) standard test requires the input sinusoidal signal to be 3-4 b better than that of the ADC under test. Such high-quality sine waves are extremely difficult to generate and challenging to implement cost effectively. This paper presents a novel method that is capable of generating a high-purity sine wave using a nonlinear digital-to-analog converter (DAC), whose purity is significantly better than the original DAC output. In addition, with the aid of the low-cost DAC-ADC co-testing method, both DAC and ADC linearity information are accurately obtained with only 1 hit per code. Therefore, it is possible to add DAC linearity information to the DAC input codes, which cancels the nonlinearity of the DAC at output to achieve high purity. The proposed method has been validated by extensive simulation and measurement results, which demonstrated its accuracy and robustness against different resolutions, structures, or performance of the ADCs/DACs. With its low cost and easy test setup, such high-purity sine wave can be widely used for various applications where precision testing is required. In addition, the ADC and DAC linearity information is accurately obtained at the same time without any precision instrumentation, which is suitable for accurate DAC-ADC co-testing.
13 July 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper introduces a 12 bit 2.5 bit/cycle SAR-based pipeline ADC employing a self-bias gain boosting amplifier. The single-stage amplifier achieves a low-frequency gain of 37 dB, while consuming 1.3 mW of power consumption with 1.3 V of analog power supply. A 2.5 bit/cycle SAR ADC realizes as the sub-ADC in each stage, and reduces both power consumption and silicon area. A two-channel sampling architecture is employed to double the sampling rate and thereby maximize circuit efficiency. A digital calibration technique is used to reduce non-linearity and mismatches due to the RDAC, as well as gain error and offset of the open-loop residue amplifier. The prototype ADC was fabricated in TSMC 40-nm technology, and consumes 10.71 mW with 1.1 V / 1.3 V digital / analog power supplies. When operating at 125 MS/s, the ADC achieves an SFDR of 66.59 dB before calibration and 80.3 dB after calibration when measured at Nyquist frequency. The experimental results show a Walden FoM of 101 fJ/c.-s. before calibration and 47 fJ/c.-s. after calibration.
16 April 2019 in IEEE Transactions on Instrumentation and Measurement
A novel ultrafast and low-cost pipelined analog-to-digital converter (ADC) testing and calibration method is proposed. The ADC nonlinearities are modeled as segmented parameters with interstage gain errors. During the test phase, a pure sine wave is sent as input and the model parameters are estimated from the output data with the system identification method. Significantly, fewer samples are required when compared to traditional histogram testing. The modeled errors are then removed from the digital output codes during the calibration phase. Extensive simulations have been run to verify the correctness and robustness of the proposed method. With just 4000 samples, a 12-bit ADC can be accurately tested and calibrated to achieve less than 1 least significant bit (LSB) integral nonlinearity (INL). Measurement results show that the ADC effective number of bits (ENOB) is improved from 9.7to 10.84 bits and the spurious-free dynamic range (SFDR) is improved by 20 dB after calibration. The chip is fabricated in 40-nm technology and consumes 10.71 mW at a sampling rate of 125 MS/s.