Tohid Sharifi

Tohid Sharifi

Auto-generated profile, based on publicly available information

Tohid Sharifi

Department of Electrical Engineering, Electrical Machines and Transformers Research Laboratory (EMTRL) Amirkabir University of Technology (Tehran Polytechnic) Tehran Iran

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

17 November 2024 in Results in Engineering
Verified
Journal Article
Open access
TSTohid Sharifi
Tohid Sharifi
AEAlireza Eikani
Alireza Eikani

18 May 2021
Verified
Conference Paper
Closed access
TSTohid Sharifi
Tohid Sharifi
DMDr. Mojtaba Mirsalim
Dr. Mojtaba Mirsalim
High torque density is a demanding criterion in electrical machines. Machines with permanent magnet (PM) in their structure possess this feature inherently. On the other hand, in the motors with no PM material, torque density is a source of concern for machine designers. So, the optimization methods should be used in the design process to achieve the best performance in terms of torque density. Biogeography-based optimization (BBO) is a relatively new algorithm with good convergence in the least time. In this paper, the structure of a synchronous reluctance (SyncRel) motor with no PM material is optimized using the BBO method. Presentation of the mathematical relations and basics of BBO is conducted. BBO algorithm settings and the parts of the optimization problem are also introduced. ANSYS MAXWELL simulates the structure of the optimized machine. Then, the optimized and initial designs are compared, and the results show that the optimized motor improves the torque density by 100 % . BBO also keeps the value of torque ripple under 20% that is an acceptable value in terms of machine performance. To evaluate the performance of the BBO, the last part of the paper presents the convergence rate and the iteration table of the BBO.

22 January 2025 in IET Electric Power Applications
Verified
Journal Article
Open access
TSTohid Sharifi
Tohid Sharifi
Permanent magnet synchronous motors (PMSMs) experience considerable performance degradation due to the rise in temperature and the resulting partial demagnetisation in the PMs, as well as the shortenings in the insulations' lifetime. To mitigate the temperature of motor components, it is crucial to investigate and continually improve the design of efficient cooling systems. This study implements the water immersion cooling (WIC) concept on a surface‐mounted PMSM (SMPMSM), where through comparing its cooling performance with the forced ventilation cooling (FVC), it is indicated that, even at high inlet velocities for the latter, it cannot maintain the temperature below the specified thresholds and the required input electric power to run the ventilation fan will be increased exponentially to compensate for its ineffectiveness. While in the WIC configuration, the winding and PM temperature values remain well below the margins when the heat transfer coefficient of this method is 40 higher than the FVC. By incorporating the effect of the cooling process through the heat transfer coefficient, the lumped‐parameter thermal network (LPTN) is utilised to study the operation mode of the motor under the mentioned cooling configurations. Besides achieving higher cooling efficiency, the WIC strategy can quickly reduce temperature, which is reflected in the thermal time constant of the cooling method extracted from the LPTN. Consequently, it is demonstrated that up to 35 higher than the nominal generated heat, the SMPMSM under the WIC can operate continuously, while for the FVC, the frequent start‐stop driving scenario should be employed.

30 January 2025 in IET Electric Power Applications
Verified
Journal Article
Open access
SSSadjad Shafiei
Sadjad Shafiei
TSTohid Sharifi
Tohid Sharifi
MDMohammad Ali Noroozi Dehdez
Mohammad Ali Noroozi Dehdez
MBMehdi Bagheri
Mehdi Bagheri
This study proposes a modified partitioned‐stator flux‐switching permanent magnet (PS‐FSPM) machine and reduces the permanent magnet usage in conventional PS‐FSPM machines. To achieve this goal, the stators of the conventional PS‐FSPM with outer‐armature/inner‐PM (OA/IPM PS‐FSPM) structure are swapped to realise a PS‐FSPM with outer‐PM/inner‐armature (OPM/IA PS‐FSPM) design. The machine topology along with the operating principles are described in detail, and an analytical airgap permeance model is introduced for the proposed machine. The number of rotor modules, the widths of the magnets and rotor modules, as well as the split ratio (SR), are optimised through sensitivity analysis to achieve higher torque density and reduced torque ripple, compared with the conventional structure. Moreover, a flux barrier in the exterior surface of the outer stator is adopted to improve the proposed structure to reach a higher flux concentration in the airgap and reduce iron volume consumption. The thermal analysis results using the computational fluid dynamics modelling indicate that the temperatures of both insulation and permanent magnets remain within specified operating limits. Finally, apart from the finite element analysis (FEA), an experimental study is performed to evaluate the feasibility of fabricating a machine equipped with a high number of rotor modular teeth.