19 December 2019 in Solid-State Electronics
6 November 2019 in Japanese Journal of Applied Physics
We investigated the growth behavior of GaN grown on AlN along with V/III ratio and pressure variation, and found out the lateral growth regime for the fully coalesced channel layer of the AlN-based double-hetero structure high electron mobility transistor (HEMT). When the V/III ratio increases and pressure decreases, compressive stress in the GaN channel increases, and pit formation occurs to release the stress. The AlN-based HEMT structure was grown and the device was fabricated with an optimized channel layer. The two-dimensional electron gas mobility, sheet density, and sheet resistance were 1480 cm 2 V −1 s −1 , 1.32 × 10 13 cm −2 , and 319 Ω/sq., respectively, at room temperature. The device was characterized; direct current output result showed that the maximum current was ∼620 mA mm −1 , on-resistance was 6.4 Ω mm, transconductance was ∼140 mS mm −1 , and current on/off ratio was ∼10 4 , respectively.
3 June 2024 in Japanese Journal of Applied Physics
In this work, we demonstrate that GaN can be directly grown at high temperature on Si(111) substrates by metalorganic CVD without using any intentional AlN buffer, by simply employing a trimethylaluminum (TMAl) preflow. We found that n-GaN layers directly grown on n-Si with a TMAl preflow not only present a better crystalline quality compared to the use of thin AlN buffers, but also exhibit orders-of-magnitude improvement in vertical current conduction between GaN and Si, thanks to the absence of highly resistive AlN layers. Our proposed technique opens a new pathway for the effective realization of fully-vertical GaN-on-Si devices.
7 March 2025 in IEEE Electron Device Letters
In this work, we introduce a p-NiO/LiNiO stack grown via low-temperature deposition processes, offering an effective alternative for creating localized p-type regions in GaN devices. This stack combines a high hole concentration p-NiO film ([h] = 2 × 1019 cm−3) with an epitaxially crystalline p-LiNiO film, resulting in a high-quality p-type layer that can be flexibly deposited and patterned on GaN devices. Here, we investigate the transport and breakdown properties of the p-NiO/LiNiO-GaN heterojunction by fabricating a p-NiO/LiNiO-GaN PiN diode. The PiN diode exhibited excellent electrical performance, including a low turn-on voltage (VON) of 1.7 V, a low specific on-state resistance (RON, sp) of 1.15 mΩ·cm2, and a high breakdown voltage (BV) exceeding 1000 V, comparable to those achieved with epitaxial GaN homojunctions. These results highlight the potential of utilizing conductive and compatible p-NiO/LiNiO stacks to replace p-GaN for high-quality localized p-n junctions, simplifying the manufacturability of GaN-based devices and enabling advanced device concepts where p-GaN is challenging to be implemented.
1 April 2021 in AIP Advances
Creating voids between thin films is a very effective method to improve thin film crystal quality. However, for AlN material systems, the AlN layer growth, including voids, is challenging because of the very high Al atom sticking coefficient. In this study, we demonstrated an AlN template with many voids grown on AlN nanorods made by polarity selective epitaxy and etching methods. We introduced a low V/III ratio and NH3 pulsed growth method to demonstrate high-quality coalesced AlN templates grown on AlN nanorods in a metal organic chemical vapor deposition reactor. The crystal quality and residual strain of AlN were enhanced by the void formations. It is expected that this growth method can contribute to the demonstration of high-performance deep UV LEDs and transistors.
26 January 2026 in Applied Physics Letters
We investigate the influence of AlN buffer thickness on the structural, electrical, and thermal properties of AlGaN/GaN high-electron mobility transistors (HEMTs) grown on semi-insulating SiC substrates by metal-organic chemical vapor deposition. X-ray diffraction and atomic force microscopy reveal that while thin AlN layers (120 nm) exhibit compressive strain and smooth step-flow surfaces, thicker single-layer buffers (550 nm) develop tensile strain and increased surface roughness. Multi-layer buffer structures up to 2 μm alleviate strain and maintain surface integrity. Low-temperature Hall measurements confirm that electron mobility decreases with increasing interface roughness, with the highest mobility observed in the structure with a thin AlN buffer. Transient thermoreflectance measurements show that thermal conductivity (ThC) of the AlN buffer increases with the thickness, reaching 190 W/m.K at 300 K for the 2 μm buffer layer, which is approximately 60% of the bulk AlN ThC value. These results highlight the importance of optimizing AlN buffer design to balance strain relaxation, thermal management, and carrier transport for high-performance GaN-based HEMTs.