1 October 2018 in Physics of Fluids
Cavitation and the energy associated with the collapse of resulting cavitation bubbles constitute an important research subject. The collapse of the hydrodynamic cavitation bubbles at the outlet of the flow elements leads to a high energy release and generates localized shock waves and a large temperature rise on exposed surfaces. The concept of “hydrodynamic cavitation on chip” is an emerging topic which emphasizes phase change phenomena in microscale and their utilizations in energy and biomedical applications. This study is aimed to investigate the potential of poly(vinyl alcohol) (PVA) Microbubbles (MBs) to generate cavitation bubbles and to evaluate their effects on flow regimes and energy dissipation. For this, three different microchannel configurations with different roughness elements were considered. The structural side wall and surface roughened channels were fabricated along with the smooth channel according to the techniques adopted from semiconductor based microfabrication. The upstream pressure varied from 1 to 7 MPa, and the flow patterns were recorded and analyzed using a high-speed camera. The pressure was locally measured at three locations along the microfluidic devices to determine the conditions for fully developed cavitating flows. The results were compared to the pure water case, and different trends for the cavitating flow pattern transitions were obtained for the water-PVA MB solution case. Accordingly, the twin cavity clouds extended to the end of the side wall roughened channel at a lower upstream pressure for the case of PVA MBs, while the smooth and surface roughened channels do not demonstrate this flow pattern. In addition, the cavitation number has the lowest values under the same working conditions for the case of PVA MBs. Moreover, the impact pressure generated by the bubble collapse inside the side wall roughened channel for the case of PVA MBs was notably higher than that for pure water.
26 August 2021 in Frontiers in Materials
Pitting corrosion seriously harms the service life of oil field gathering and transportation pipelines, which is an important subject of corrosion prevention. In this study, we collected the corrosion data of pipeline steel immersion experiment and established a pitting judgment model based on machine learning algorithm. Feature reduction methods, including feature importance calculation and pearson correlation analysis, were first adopted to find the important factors affecting pitting. Then, the best input feature set for pitting judgment was constructed by combining feature combination and feature creation. Through receiver operating characteristic (ROC) curve and area under curve (AUC) calculation, random forest algorithm was selected as the modeling algorithm. As a result, the pitting judgment model based on machine learning and high dimensional feature parameters (i.e., material factors, solution factors, environment factors) showed good prediction accuracy. This study provided an effective means for processing high-dimensional and complex corrosion data, and proved the feasibility of machine learning in solving material corrosion problems.
1 February 2020 in AIP Advances
In this study, cavitating flows inside a transparent cylindrical nozzle with an inner diameter of 0.9 mm were visualized, and the effect of cavitation on atomization characteristics of emerging sprays was investigated. Different patterns of cavitating flows inside the nozzle were visualized using a high-speed camera. In-house codes were developed to process the captured images to study the droplet size distribution and droplet velocity in different flow regimes. The results show that cavitating flows at the microscale have significant effects on atomization characteristics of the spray. Two working fluids, namely, water and poly(vinyl alcohol) microbubble (PVA MB) suspension, were employed. Accordingly, the injection pressures were detected as 690 kPa, 1035 kPa, and 1725 kPa for cavitation inception, supercavitation, and hydraulic flip flow regimes in the case of water, respectively. The corresponding pressures for the aforementioned patterns for PVA MB suspension were 590 kPa, 760 kPa, and 1070 kPa, respectively. At the microscale, as a result of a higher volume fraction of cavitation bubbles inside the nozzle, there is no large difference between the cavitation numbers corresponding to cavitating and hydraulic flip flows. Although the percentage of droplets with diameters smaller than 200 μm was roughly the same for both cases of water and PVA MB suspension, the Sauter mean diameter was considerably lower in the case of PVA MBs. Moreover, higher droplet velocities were achieved in the case of PVA MBs at lower injection pressures.
27 November 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Contrast agents are routinely used in ultrasound examinations. Nonlinear ultrasound imaging techniques have been developed over decades to enhance the contrast between the tissue and the blood pool after the injection of ultrasound contrast agents. In this study, we introduce a new contrast pulse sequence, CPS4. The CPS4 combines pulse inversion, sub-harmonic, and ultra-harmonic techniques to remove propagation distortion while capturing the unique sub-harmonic, and ultra-harmonic responses from ultrasound contrast agents. The novel CPS4 and conventional pulse inversion, sub-harmonic, and ultra-harmonic techniques were used to detect the presence of a research-grade, thick shell, polymer microbubble in a tissue-mimicking flow phantom. The contrast-to-tissue ratio (CTR) obtained from the applications of all techniques were compared. The results show that the highest CTR of approximately 16 dB was obtained using CPS4, which was superior to the individual reference techniques: pulse inversion, sub-harmonic, and ultra-harmonic techniques, at all scenarios considered in this study.
17 February 2021 in ACS Omega
Acoustic droplet vaporization (ADV) is the physical process of liquid-to-gas phase transition mediated by pressure variations in an ultrasound field. In this study, the acoustic response of novel particle-stabilized perfluoropentane droplets was studied in bulk and confined media. The oil/water interface was stabilized by cellulose nanofibers. First, their acoustic responses under idealized conditions were examined to assess their susceptibility to undergo ADV. Second, the droplets were studied in a more realistic setting and placed in a confined medium. Lastly, an imaging setup was developed and tested on the droplets. The acoustic response could be seen when the amplitude of the peak negative pressure (PNP) was above 200 kPa, suggesting that this is the vaporization pressure threshold for these droplets. Increasing the PNP resulted in a decrease in signal intensity over time, suggesting a more destructive behavior. The imaging setup was able to differentiate between the droplets and the surrounding tissue. Results obtained within this study suggest that these droplets have potential in terms of ultrasound-mediated diagnostics and therapy.