18 September 2012 in Energy & Environmental Science
We proposed a simple yet robust film treatment method with methanol having only one hydroxyl group to enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) by four orders of magnitude. Different methods of film treatment: immersing PEDOT:PSS film in the methanol solution; dropping methanol on the film; and a combination of these are employed and the results are compared. The conductivity of PEDOT:PSS films was enhanced from 0.3 S cm−1 to 1362 S cm−1 after film treatment with methanol. Other alcohols like ethanol and propanol were also used to treat the PEDOT:PSS film and showed inferior conductivity enhancement compared to methanol. The conductivity enhancement was greatly affected by the hydrophilicity and dielectric constant of the alcohols used. The mechanism of conductivity enhancement was investigated through various characterization techniques including FTIR, XPS and AFM. Removal of the insulator PSS from the film, and morphology and conformational changes are the mechanisms for the conductivity enhancement. The treated films also showed high transmittance and low sheet resistance desirable for a standalone electrode. ITO-free polymer solar cells were fabricated using PEDOT:PSS electrodes treated with methanol and showed almost equal performance to ITO electrodes.
18 June 2012 in Chemical Communications
Nanoporous carbons with high surface area are achieved through direct carbonization of a commercially available zeolitic imidazolate framework (ZIF-8) without any additional carbon sources. The resultant nanoporous carbons exhibit high electrochemical capacitances in an acidic aqueous electrolyte.
14 June 2013 in Journal of Materials Chemistry A
We systematically investigated the effect of the molecular weight of additives on the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) by using different concentrations and molecular weights of polyethylene glycol (PEG) and ethylene glycol (EG). The conductivity enhancement depends on both the molecular weight and concentration of PEG used. The conductivity of PEDOT:PSS was enhanced from 0.3 S cm−1 to 805 S cm−1 with 2% PEG but to only 640 S cm−1 with 6% EG. PEGs with molecular weight higher than 400 have too low mobility to impart the required screening effect, and hence, the conductivity enhancement is less. Through FTIR, XPS and AFM investigations, the mechanism for the conductivity enhancement is found to be charge screening between PEDOT and PSS followed by phase separation and reorientation of PEDOT chains leading to bigger and better connected particles. The molecular weight and concentration of PEG also affect solar cell performances even though the conductivities are the same. Due to their high conductivity and high transmittance, ITO-free organic solar cell devices fabricated using PEDOT:PSS treated with 2% PEG anodes exhibited performance almost equal to that of the ITO counterparts.
13 September 2017 in Journal of Materials Chemistry A
KBKarunakara Moorthy Boopathi
Karunakara Moorthy Boopathi
PKPriyadharsini Karuppuswamy
Priyadharsini Karuppuswamy
+4
Organic–inorganic lead halide perovskites have recently emerged as highly competitive light absorbing materials for low cost solution-processable photovoltaic devices. With the high efficiency already achieved, removing the toxicity, i.e., lead-free and stability are the key obstacles for perovskite solar cells. Here, we report the synthesis of an antimony (Sb)-based hybrid material having the composition of A3Sb2I9 [A = CH3NH3 (MA), Cs] and an investigation of its potential photovoltaic applications. Sb-based perovskite-like materials exhibited attractive absorbance properties, with the band gaps of MA3Sb2I9 and Cs3Sb2I9 measured to be 1.95 and 2.0 eV, respectively. X-ray photoelectron spectroscopy confirmed the formation of stoichiometric perovskites from appropriate precursor molar ratios incorporated with hydroiodic acid (HI). Planar hybrid Sb-based solar cells exhibited negligible hysteresis and reproducible power output under working conditions. A power conversion efficiency of 2.04% was achieved by the MA3Sb2I9 perovskite-based device—the highest reported to date for a Sb-based perovskite solar cell.
7 January 2016 in Journal of Materials Chemistry A
KBKarunakara Moorthy Boopathi
Karunakara Moorthy Boopathi
+2
Alkali metal halide additives chelate with Pb2+ ions during film formation promoting homogeneous nucleation, which greatly enhances the power conversion efficiency (15.08%) and stability (over 50 days) of planar perovskite solar cells.
10 December 2019 in Journal of Materials Chemistry A
Over the past decade, intensive research efforts have been directed toward the field of organic–inorganic hybrid perovskites, with dramatic progress made in both the photovoltaic performance and device stability. Therefore, it has become the fastest growing photovoltaic research area. Perovskite materials use low-cost earth-abundant elements and can be solution-processed; furthermore, the technology is compatible with large-scale roll-to-roll manufacturing. Recently, the successful demonstration of the photovoltaic performance of perovskites reaching that of the commercialized monosilicon photovoltaic technology combined with the significantly improved stability has made scaling-up the perovskite PV technology to become a new research area, which is the topic of this review. First, the fundamental background knowledge of classical nucleation and crystal growth from a solution is summarized along with its application in perovskite film evolution. We then discuss the common perovskite PV device architectures and perovskite layer deposition methods, followed by summarizing scalable solution approaches with recent progress and related challenges for the scaling-up process. Upon the introduction of the current in-depth understanding of perovskite nucleation and crystal growth, external strategies (including both physical and chemical approaches) controlling the perovskite film formation are reviewed in diverse scalable manufacturing methods. Overall, aiming at overcoming the challenges of transferring from laboratory research, we provide an overview of achieving high-performance perovskite solar cells by using scalable fabrication methods via precise nucleation and crystal growth control during the perovskite film formation process.