α-MgAgSb is a promising p-type thermoelectric (TE) with excellent performance from room temperature up to 300 °C with a figure of merit of zTmax = 1.3. This makes MgAgSb a potential Te-free bismuth telluride (Bi2Te3) substitute for cooling and waste heat conversion applications. However, the material is also known for its sensitivity on synthesis conditions as indicated by various reports on the same nominal composition which show greatly differing TE properties and performance. This indicates a fundamental lack of synthesis control and synthesis–composition–property relationship knowledge. In this work, we establish a modified synthesis route with improved control over the effective sample stoichiometry which allows for reproducible high-performance properties (zTmax = 1.34 ± 0.19 at 561 K) and for systematically targeting different thermodynamic states of MgAgSb. This phase boundary mapping reveals that the homogeneity range for MgAgSb is very small (<0.1 at%) and that the TE properties are not governed by different thermodynamic states. Instead, we rationalize that the TE performance of MgAgSb is mainly controlled by the amount and type of secondary phases, mainly affecting the carrier mobility. We conclude that Sb-excess related secondary phases are the least detrimental, leading the way to upscaled synthesis of high-performance material.
Mg2(Si,Sn) shows great promise as thermoelectric material as it is made from non‐toxic, abundant, and cost‐effective elements offering high performance. This has been emphasized by several thermoelectric generator prototypes, demonstrating technological maturity. However, material stability is paramount for large‐scale applications whereas we reveal here that the thermal stability of n‐type Mg2(Si,Sn) may be limited even at room temperature (RT). Integral thermoelectric properties measurements, locally resolved Seebeck coefficient analysis, scanning electron microscopy/energy‐dispersive X‐ray spectroscopy, and atomic force microscopy are employed to assess changes of n‐type samples stored in ambient atmosphere for years, revealing the evolution of the carrier concentration and transport properties in the material as well as surface degradation. This is caused by the diffusion of loosely bound Mg from the bulk towards the surface and subsequent oxidation, leading to a change of Mg‐based intrinsic defect concentrations, thereby degrading the thermoelectric performance. This microscopic mechanism is backed up by first‐principles calculations, revealing that Mg diffusivity in Mg2(Si,Sn) is high at RT and that diffusion occurs mainly via Mg vacancies. The observed much faster degradation of Sn‐rich Mg2(Si,Sn) can be correlated with the higher density of Mg vacancies in Mg2Sn compared to Mg2Si, as predicted from defect formation energies.
Mg2(Si,Sn)-based semiconductors constitute promising thermoelectrics (TE), in particular as n-type materials. These are usually synthesized under Mg-excess to compensate for losses of Mg during synthesis and achieve the high carrier concentration required for optimal performance. However, this usage of excess Mg leads to loosely bound Mg in the material which is easily lost during operation, leading to a fast and massive degradation of the TE performance. In this work, we introduce Mg-poor n-type Mg2(Si,Sn), avoiding excess and loosely bound Mg. We find that (i) employing relatively large nominal Mg deficiency leads nevertheless to single-phase, Mg-poor Mg2(Si,Sn) by a self-adjustment of the composition during sintering, and (ii) that despite showing a lower dopant efficiency, Sb can be employed to achieve the required optimum carrier concentration, resulting in a figure of merit of zT = 1.2 ± 0.2 at 700 K, comparable to Mg-rich samples. This is confirmed by a comparison of Mg-rich and Mg-poor samples in a single parabolic band model which reveals similar microscopic material parameters such as weighted mobility and scattering constants. Finally, we compare Mg-poor synthesized samples with initially Mg-rich ones that experienced Mg loss. Despite similar global compositions we identify grain boundary scattering to be more pronounced in Mg-depleted samples, marking one of the fundamental reasons for the performance degradation of synthesized Mg-rich synthesized samples. Overall, this work highlights the importance of grain boundaries on grain boundaries for the performance of TE materials and the successful application of thermodynamic degrees of freedom to address fundamental challenges in TE material systems while retaining promising TE performance.
The p-type thermoelectric (TE) material α-MgAgSb is a promising tellurium-free bismuth telluride substitute for cooling and waste heat harvesting applications between room temperature and 573 K. Optimization of the material resulted in high values of figure of merit (zTmax = 1.3) to date, but performance optimization of TE devices also requires minimizing the electrical contact resistance between the TE material and the electrodes. Here, we investigate the metallization of MgAgSb with MgCuSb, providing microstructural and electrical analyses of the interfaces for functionalized legs obtained from a combined sintering of both materials systematically varying temperature, duration and pressure. Analysis of the obtained results reveals the formation of an interdiffusion layer of Ag3Sb with varying thickness in all samples, but the contact resistance remains consistently below 10 μΩ cm2. Microprobe measurements of the Seebeck coefficient indicate a change in carrier concentration in the TE material close to the interface, visualizing interdiffusion processes between MgAgSb and MgCuSb. We furthermore demonstrate that MgCuSb can successfully be applied as an electrode on pre-compacted MgAgSb samples, resulting in the first ever reported successful two-step contacting of MgAgSb. The obtained sample exhibits a strong mechanical contact without any crack at the interface, as well as a very low electrical contact resistance below 7 µΩ cm2, representing less than 5% of the total leg resistance. Successful contacting of pre-compacted material is a step forward towards module fabrication as it enables better control of the TE leg length and thus device performance.
A thorough understanding and optimization of microstructure are key for enhancing performance in thermoelectric materials. By combining high‐resolution microstructural analysis with bulk transport characterization and spatially resolved Seebeck microprobe measurements, the interrelation between phase constitution and thermoelectric properties of MgAgSb, a promising p‐type room temperature material is established. This study analyzes 35 MgAgSb samples with varying compositions and synthesis conditions. Scanning transmission electron microscopy with energy‐dispersive X‐ray spectroscopy and selected area electron diffraction reveals that remnants of constituent elements from the initial synthesis step can cause the formation of detrimental secondary phases, including a previously unnoticed, highly dispersed Ag 3 Sb nanophase uniformly distributed throughout the samples. Analysis of the temperature dependence of the weighted mobility reveals differences in carrier scattering as the main reason for the different thermoelectric performance. Furthermore, a statistical analysis of weighted mobility and material quality factor versus type and amount of secondary phase reveals the secondary phases to predominantly affect the electronic (not thermal) transport, ranks them according to impact and further distinguishes classical mixing from grain boundary effects. This approach is crucial for understanding how specific phases affect material performance, identifying Mg 3 Sb 2 and (Ag) as the most detrimental, but also providing guidelines for further material improvement.