The heat transfer and wake-induced vibrations of a cylinder of circular cross-section in the wake of another identical cylinder is numerically studied in this work at Reynolds number (Re) = 100. The reduced velocities (Ur) are varied in the range of 2 - 14. The downstream cylinder is allowed to oscillate in 2DOF, i.e., in transverse as well as in streamwise direction. The mass ratio (m*) is taken as 10 while the structural damping is ignored to get the maximum amplitude of vibration. The spacing ratio (L/D) between the cylinders is varied from 1.5 - 6 covering the major regimes, i.e., single body, reattachment, and co-shedding. The coefficients of lift (CL) and drag (CD), vibrational amplitudes of the cylinder, Nusselt number (Nu), Strouhal number (St), and vortex shedding patterns are studied. The lock-in condition at Ur = 8 is observed for all values of L/D, whereas the lock-in zone is the widest for the co-shedding regime at L/D = 6. Increasing L/D from 1.5 to 2.5 at Ur = 8, the CL of downstream cylinder increases by 43%, whereas for upstream cylinder decreases by 61%. A maximum decrease in the average drag coefficient of 107%, as compared to the stationary isolated cylinder, was observed for downstream cylinder at L/D = 1.5 and Ur = 2. Mostly, the 2S and C(2S) vortex shedding pattern is observed. Increasing L/D the average Nu for both upstream and downstream cylinder increases as the effect of each cylinder on the other diminishes.
This study investigates the impact of arrangement of two cylinders on their flow-induced vibrations (FIV) and heat transfer behavior at a Reynolds number of 100. Both cylinders were allowed to vibrate in two degrees of freedom (2DOF), encompassing streamwise and transverse directions. The arrangement of identical circular cylinders was varied across tandem (α = 0°), staggered (α = 30°, 45°, 60°), and side-by-side (α = 90°) configurations, at a constant center-to-center distance of 6D. The cylinders were heated at a fixed temperature to observe the forced convection heat transfer behavior under the influence of 2DOF FIV. To observe the FIV, the reduced velocity was varied from Ur = 0 (stationary cylinders) to 14. Results unveiled cylinder response sensitivity, encompassing vibration and heat transfer, with respect to reduced velocities and arrangements. Tandem arrangement exhibited the greatest vibrations for both cylinders. While lower drag was experienced in tandem for cylinder 2 (C-2), it escalated in staggered positioning. Both cylinders experienced lock-in between Ur = 6 and 8 for all arrangements, involving significant transverse vibration amplitudes. Maximum streamwise vibration reached 6.07% of the maximum transverse vibration for C-2 and 2.34% for C-1. Distinct slender “figure-8” and “oval-shaped” cylinder trajectories emerged, accompanied by diverse vorticity patterns in cylinder wakes across arrangements. For α = 60°, C-2 experienced 75.3% lower transverse vibration and 9.4% higher average Nusselt number compared to tandem setup. Overall, a pronounced correlation emerged between cylinder hydrodynamic behavior and heat transfer characteristics, evident through cylinder vibration, vortex shedding, average Nusselt number, and temperature distribution results.
7 November 2022 in European Journal of Mechanics - B/Fluids
This research delves into the performance enhancement of Vertical Axis Wind Turbines (VAWTs) through the innovative approach of variable blade pitching based on Double Multiple Stream Tube theory principles. VAWTs, known for their potential in urban and low-wind environment, often face efficiency and energy yield challenges. This study addresses these challenges by proposing a novel variable blade pitching mechanism that dynamically adapts to changing wind conditions, optimizing the aerodynamic performance, and enhancing the torque and overall performance of VAWT rotor. The efficiency of two pitching models is investigated on 3-bladed NACA0015 rotors, where the blade's local angle of attack is cyclically adjusted below the stall angle to maximize the lift force and torque throughout full revolution. In Model 1, the angle of attack experiences cyclic variation as a sinusoidal function providing smooth pitching, whereas in Model 2, the peak value of angle of attack was fixed below the stall condition forming linear function. The investigation showed substantial improvement in the VAWT performance using both pitching models. The variable blade pitching strategy significantly enhances the lift-to-drag ratio and thus improving the torque output across diverse wind scenarios/tip speed ratios, demonstrating its effectiveness in maximizing the operational efficiency of VAWTs. Blade pitching model 1 and 2 were found to be effective across all lower Tip Speed Ratio (TSR) values, suggesting its robustness in variable wind conditions. A peak average coefficient of performance (Cp) of 0.568 was achieved at TSR = 5 using pitching Model 1 with a maximum angle of attack of 8.5°, compared to a Cp of 0.48 for the fixed blade configuration, near to Betz's limit (Cp = 0.593). The findings confirm that integrating variable blade pitching would substantially improve VAWT performance and offer a clear direction for revolutionary future wind turbine aerodynamic design enhancements.