Md. Ali Asgar

Md. Ali Asgar

Auto-generated profile, based on publicly available information

Md. Ali Asgar

Department of Electrical and Electronic Engineering Jatiya Kabi Kazi Nazrul Islam University Trishal Bangladesh

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2024 in International Journal of Energy Research
Verified
Journal Article
Open access
PDF file
AAAli Asgar
Ali Asgar
CTChau Van Tran
Chau Van Tran
JKJUN KIM
JUN KIM
CJChengjun Jin
Chengjun Jin
SLSeongmin Lee
Seongmin Lee
SKSeok-Min Kim
Seok-Min Kim
Hierarchical porous carbon materials have received significant attention for application in catalytic water splitting because of their high efficiency, cost‐effectiveness, and biocompatibility. In this study, laser‐induced graphene (LIG) was fabricated on a carbon film‐ (CF‐) type substrate for an efficient hydrogen evolution reaction (HER). The LIG‐CF electrode was fabricated via laser‐induced graphitization on a commercial polyimide (PI) film, followed by the pyrolysis of the LIG on the PI film (LIG‐PI). During pyrolysis, the microscopic and material properties of the LIG remained intact, as verified through various characterizations. The as‐prepared all‐carbon electrode was then utilized as an electrode for the HER study in a 1.0 M KOH electrolyte and compared with LIG‐PI and Pt electrodes. In the HER experiments, the optimized LIG‐CF electrode exhibited excellent catalytic performance with zero‐onset potential, and the potentials required to achieve high current densities of 10 and 20 mA/cm2 were 134 and 139 mV (vs. reversible hydrogen electrode (RHE)), respectively. The excellent performance of the LIG‐CF electrode originates from the hierarchical porous structure of the LIG material, which serves as an electrochemically active site, and carbon substrate that facilitates the fast transport of ions at the electrode/electrolyte interface. Additionally, the carbon substrate shortens the transportation length of electrons which played a significant role for the enhanced performance of the LIG‐CF electrode.

10 September 2026 in Advanced Materials Technologies
Verified
Journal Article
Open access
MAMuzahir Ali
Muzahir Ali
SLSeongmin Lee
Seongmin Lee
THTasadduq Hussain
Tasadduq Hussain
YKYoung Kyu Kim
Young Kyu Kim
MAMd. Ali Asgar
Md. Ali Asgar
SKSeok-Min Kim
Seok-Min Kim
Architected electrodes that improve catalytic activity, mass transport, and scalability in one system are critical in the progression of alkaline water electrolysis. However, most 3D printed systems require multistep post‐fabrication modifications and consequently, the catalyst is only integrated into surface layers, leading to poor stability. Here, we demonstrate a print‐to‐catalyst approach integrated with nickel and phosphorus precursors directly into digital light processing (DLP) resin that can be used to fabricate programmable Ni–P‐doping porous carbon microlattices for scalable fabrication with in situ processes for the activation of active phases in carbonization. This type of approach incorporates structural and chemical design, where lattice topology is optimized giving minimal transport losses and identifying an X‐Cell geometry with favorable limitations for electrolyte penetration and gas bubble removal, with Ni loading and phosphorus incorporation modulating the electronic structure of Ni to create efficient Ni–P–O–C active interfaces. Comprehensive characterization confirms homogeneous dispersion of Ni, NiO x and Ni–P species embedded in carbon structure to produce catalytically active interfaces. The overpotential of the optimized electrode is 106 mV at 10 mA cm −2 in 1 M KOH, and the electrode's low charge transfer resistance and stable operation for 100 h are also observed.