Joachim Holtz

Joachim Holtz

Auto-generated profile, based on publicly available information

Joachim Holtz

University of Wuppertal, Wuppertal, Germany

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 December 2014 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Open access
JHJoachim Holtz
Joachim Holtz
GCGilberto da Cunha
Gilberto da Cunha
NPNorton Petry
Norton Petry
PTPaulo José Torri
Paulo José Torri
High-power grinding mills are used in the cement and mining industries to crush clinker or copper ore and grind these materials to fine powder. The multimegawatt speed-controlled mill drives operate at a very low angular speed. Synchronous motors with a high number of pole pairs are used as the prime movers. They are traditionally fed by load-commutated thyristorized cycloconverters. These are prone to failure modes that can lead to excessive torque pulsations and high overcurrents. The huge stator, which was built as a separate ring-shaped structure around the tubular mill, may then get mechanically displaced, and the operation of the plant is interrupted. A novel and reliable direct drive uses a voltage source inverter that operates at the unity power factor for increased efficiency. Synchronous optimal pulsewidth modulation ensures a low harmonic current distortion and reduced switching losses at a very low switching frequency. The optimization of the pulse patterns takes the anisotropic magnetic properties of a separately excited synchronous motor into account. The implementation in a 23-MW semiautonomous grinding mill installed in a Zambian copper mine is intended.

20 October 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JHJoachim Holtz
Joachim Holtz
A multistep predictive algorithm eliminates overshoots of the current vector outside the boundary circle while the processor identifies the next optimal switching state vector following a boundary transition. The predictions of the current vector trajectories refer to a simplified machine model consisting only of the leakage inductance. Nevertheless is good accuracy of the predictions achieved. Operation at low switching frequency minimizes both harmonic distortion and switching losses. Using higher switching frequencies does not lead to noticeable improvement over ordinary carrier modulation. Maximum fundamental output voltage is achieved by predictive overmodulation.

2 July 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
XQXin Qi
Xin Qi
JHJoachim Holtz
Joachim Holtz
Complex state variables are used to study the dynamic behavior of induction motors considering the propagation in space of the distributed magnetic field inside the machine. The objective of this paper is to improve the dynamics of pulsewidth modulation inverters in medium-voltage drive systems. To keep the dynamic losses of the power devices at a tolerable level, the switching frequency must be below 1 kHz. The sampling rate of the digital signal processing system is then low which introduces considerable signal delay. The delay has an adverse influence on the dynamic behavior of the current control system. It introduces undesired cross coupling between the current components id and iq. The degree of cross coupling is described by a cross-frequency transfer function. It is shown that the mechanism of cross coupling is different and more adverse than the conventional theory discloses. A current controller structure having poles and zeroes of the single-complex type is synthesized. Cross coupling is completely eliminated at any low switching frequency. Experimental results demonstrate that high dynamic performance and zero cross coupling is achieved even at very low switching frequency.


1 June 2007
Verified
Conference Paper
Closed access
Haitham Abu-RubHaitham Abu-Rub
Haitham Abu-Rub
HSH. Schmirgel
H. Schmirgel
JHJ. Holtz
J. Holtz
This paper presents a highly dynamic rotor flux- oriented control system of an induction motor in the field weakening region. The control system guarantees maximum torque production taking into account voltage and current limits. The approach permits operation without using a speed sensor. The system is investigated by simulation in real time and experimentally using a fixed point microcontroller.

3 January 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
JHJoachim Holtz
Joachim Holtz
Complex state variables are used to analyze the dynamics of medium voltage drives. These operate at low switching frequency to reduce the dynamic losses of the power semiconductor devices. A low sampling rate of the digital signal processing system results, causing signal delays which deteriorate the dynamic behavior. Undesired cross-coupling results between the current components id and iq. The effect is shown to be even more adverse than described by the conventional control theory. The solution is modelling the system by single-complex state variables. These permit designing a current controller of high dynamic performance which exhibits zero cross-coupling. Improved performance at very low switching frequency is demonstrated by experimental results.