Conventional aluminum (Al) and its alloys have been replaced by aluminum matrix composites (AMCs) due to their superior properties in the recent years. There are several attractive candidates as reinforcement for aluminum composites such as Al2O3, B4C and SiC. Nowadays, carbon based materials such as graphite, carbon nanotubes (CNTs) and graphene have attracted much attention owing to their above mentioned mechanical and physical properties. In this study, the wear behavior of Al graphene nanoplatelets (GNPs) composites reinforced with up to 2 wt.-% GNP were investigated. The addition of graphene up to 1 wt.-% decreased coefficient of friction. Experimental data were used to develop linear and nonlinear models. The experimental results are in good agreement with the results of the simulations based on the identified models.
27 August 2019 in Journal of Testing and Evaluation
Uniaxial tensile and uniaxial loading-unloading experiments are performed to characterize the mechanical properties of polylactic acid (PLA) manufactured by fused deposition modeling (FDM). To investigate viscoelastic and viscoplastic properties of PLA manufactured with FDM, uniaxial loading-unloading tensile tests are conducted at different strain rates. In addition, the influences of layer orientation on the mechanical properties of PLA specimens manufactured by FDM are investigated. The specimens are manufactured with a vertical and horizontal orientation. The influence of strain rate on ductility is also investigated. Decreasing the strain rate leads to an increase in strain at break. This increase in ductility is interpreted as a result of the effect on secondary bonds. Viscoplastic deformation followed by fracture is seen at lower strain rate tests. As stress and stiffness increases, ductility decreases. More ductility is seen at the horizontally oriented specimens than the vertically oriented specimens. On the other hand, the influences of layer orientation on the mechanical properties of PLA specimens are also investigated. It could be said that the tensile behavior is strain rate and manufacturing orientation dependent. As expected, the higher strain rate values yield to more brittle behavior. More brittle behavior is also reported at vertically oriented specimens. To compare with FDM specimens, injection-molded specimens are produced, and more brittle behavior is observed. Uniaxial loading and unloading tensile tests are also performed for the same specimens. It is observed that elastic recovery increases with increasing strain rate. Results showed that printing orientation does not have a major effect on elastic recovery.
In this study, multi-wall carbon nanotube (MWCNT) reinforced acrylonitrile butadiene styrene (ABS) nanocomposite filaments are produced. Filaments are examined through thermogravimetric analysis (TGA) and definitive scanning calorimetry (DSC) analysis. Produced nanocomposite filaments are used in the fused deposition modeling (FDM) process to manufacture parts. Wear tests are conducted on 3D-printed parts using wear test apparatus with an attached heating module under different ambient temperatures. Hence, the influence of CNT reinforcement, along with different FDM process parameters and varying test conditions on the wear behavior of 3D-printed ABS-CNT parts, are examined. Worn surfaces of the specimens are examined by scanning electron microscopy (SEM). Nonlinear autoregressive exogenous (NARX) models are proposed for the prediction of the wear behavior of 3D-printed ABS-CNT nanocomposites. While wear rate is taken as output, ambient temperature and amount of nanofiller are accounted as input parameters along with the variation of coefficient of friction (COF) which is obtained from measured frictional force and three input-one output model structure is proposed for NARX. The use of multiple input-single output (MISO) model structure and examining the wear behavior of 3D-printed ABS-CNT samples under different wear test conditions with different FDM process parameters are the novelties in this work.
In electric vehicles, it is important to maximize their regenerative braking performances for obtaining longer driving distances. In this study, for an electric vehicle having motors on the front and rear axles, an optimum torque distribution algorithm based on dynamic programming method is proposed for maximizing the regenerative braking energy. Electric motor limits, efficiency maps, battery model and braking force constraints given in the European regulations are considered in the proposed algorithm. The dynamic programming algorithm code and simulation studies for different braking scenarios are carried out via MATLAB. Simulation studies show that via the proposed torque distribution algorithm, significant improvements in the regenerated braking energy are obtained with respect to the fixed-rate torque distribution algorithm.
In this study, three-dimensional (3D) printed polylactic acid (PLA) samples are annealed at slightly above the glass transition temperature to enhance the mechanical properties. Tensile and Izod impact tests are conducted to investigate the mechanical properties of 3D printed PLA specimens. Influence of different infill patterns on tensile strength and impact resistance are also observed. Porous structure of 3D printed PLA specimens is examined and average void area densities are determined via scanning electron microscope (SEM) images. Influence of void area density on mechanical properties is investigated. Tensile behaviour of 3D printed PLA parts is simulated with proposed nonlinear autoregressive with exogenous and transfer function models. While stress data and determined void area densities are used as inputs, strain data obtained from tensile tests used as output for the model structures.