Kamil Feratoğlu

Dr. Kamil Feratoğlu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in Journal of Reinforced Plastics and Composites
Verified
Journal Article
Closed access
PYPasa Yaman
Pasa Yaman
OEOlcay Ekşi
Olcay Ekşi
SKSencer Süreyya Karabeyoğlu
Sencer Süreyya Karabeyoğlu
KFKamil Feratoğlu
Kamil Feratoğlu
In the study, parts are fused deposition modeling–printed using polylactic acid filaments filled with copper, brass, bronze, tungsten, and carbon fiber. Wear and three-point bending tests are applied to FDM-printed specimens and it is yielded that on-edge oriented specimens had higher flexural strength while flat orientation contributed to wear resistance. Wear tracks are examined, and mostly abrasive wear is detected in the dry sliding condition while adhesive, fatigue and abrasive wear is observed in the wet sliding condition. Brass-filled polylactic acid specimens showed highest flexural strength and flexural modulus with 46.73 MPa and 1.53 GPa, respectively. Besides, the most wear resistant filler is determined as tungsten for dry and wet sliding conditions.

13 March 2024 in Arabian Journal for Science and Engineering
Verified
Journal Article
Open access
PDF file
KFKamil Feratoğlu
Kamil Feratoğlu
IIİlyas İstif
İlyas İstif
ÖGÖmer Gümüş
Ömer Gümüş
ETErol Türkeş
Erol Türkeş
In this study, one of the most frequently used polymeric materials in fused deposition modeling (FDM) acrylonitrile butadiene styrene (ABS) is reinforced with different amount of carbon nanotubes (CNTs). Thermogravimetric analysis and differential scanning calorimetry analysis are applied to examine thermal degradation behavior of produced nanocomposite filaments. Specimens are manufactured by fused deposition modeling by using produced nanocomposite filaments. Tensile, creep and viscoelastic-viscoplastic behaviors of FDM-printed nanocomposite samples are investigated by conducting tensile, creep and loading–unloading tests under different strain rates and strain levels. Morphology of 3D printed samples is examined through scanning electron microscopy. Void densities which plays important role in mechanical behavior of additively manufactured samples are determined via ImageJ and CNT reinforcement on void densities are investigated. Data obtained from tests are used in system identification process, and multi-input–single-output model structures are proposed for the prediction of tensile, creep and recovery behaviors of 3D printed nanocomposite materials.

29 January 2021 in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Verified
Journal Article
Closed access
PDF file
SKSencer Süreyya Karabeyoğlu
Sencer Süreyya Karabeyoğlu
OEOlcay Ekşi̇
Olcay Ekşi̇
KFKamil Feratoğlu
Kamil Feratoğlu
Copper shows promising characteristics for applications in electrical sliding contacts. In this study, copper reinforced polylactic acid (PLA-copper) composites manufactured by fused deposition modeling (FDM). Wear behaviour of PLA-copper composites under dry sliding conditions at three different temperature conditions (20oC, 50oC, 70oC) was evaluated by using pin-on-disc wear test equipment with attached heating module with 5N load applied at a sliding velocity of 104.7 mm/s. Tests have presented for 1040 steel bead interacting with polymer composite. Specific wear rates and coefficient of frictions of PLA-Cu polymer composites were evaluated. EDX analysis were conducted to examine the microstructure and scanning electron microscopy is used for the characterization of the worn surfaces.

17 March 2023 in Journal of Polymer Engineering
Verified
Journal Article
Closed access
KFKamil Feratoğlu
Kamil Feratoğlu
IIIlyas Istif
Ilyas Istif
OGOmer Yunus Gumus
Omer Yunus Gumus
In this study, multi-wall carbon nanotube (MWCNT) reinforced acrylonitrile butadiene styrene (ABS) nanocomposite filaments are produced. Filaments are examined through thermogravimetric analysis (TGA) and definitive scanning calorimetry (DSC) analysis. Produced nanocomposite filaments are used in the fused deposition modeling (FDM) process to manufacture parts. Wear tests are conducted on 3D-printed parts using wear test apparatus with an attached heating module under different ambient temperatures. Hence, the influence of CNT reinforcement, along with different FDM process parameters and varying test conditions on the wear behavior of 3D-printed ABS-CNT parts, are examined. Worn surfaces of the specimens are examined by scanning electron microscopy (SEM). Nonlinear autoregressive exogenous (NARX) models are proposed for the prediction of the wear behavior of 3D-printed ABS-CNT nanocomposites. While wear rate is taken as output, ambient temperature and amount of nanofiller are accounted as input parameters along with the variation of coefficient of friction (COF) which is obtained from measured frictional force and three input-one output model structure is proposed for NARX. The use of multiple input-single output (MISO) model structure and examining the wear behavior of 3D-printed ABS-CNT samples under different wear test conditions with different FDM process parameters are the novelties in this work.

24 August 2022 in Journal of Polymer Engineering
Verified
Journal Article
Closed access
SKSencer Süreyya Karabeyoglu
Sencer Süreyya Karabeyoglu
OEOlcay Eksi
Olcay Eksi
IIIlyas Istif
Ilyas Istif
KFKamil Feratoğlu
Kamil Feratoğlu
In this study, three-dimensional (3D) printed polylactic acid (PLA) samples are annealed at slightly above the glass transition temperature to enhance the mechanical properties. Tensile and Izod impact tests are conducted to investigate the mechanical properties of 3D printed PLA specimens. Influence of different infill patterns on tensile strength and impact resistance are also observed. Porous structure of 3D printed PLA specimens is examined and average void area densities are determined via scanning electron microscope (SEM) images. Influence of void area density on mechanical properties is investigated. Tensile behaviour of 3D printed PLA parts is simulated with proposed nonlinear autoregressive with exogenous and transfer function models. While stress data and determined void area densities are used as inputs, strain data obtained from tensile tests used as output for the model structures.