21 August 2023 in IEEE Transactions on Electron Devices
Focusing on traveling wave tube (TWT) applications, the interaction impedance between an electron beam and electromagnetic modes in three distinct, but related, corrugated waveguides that operate at millimeter waves is investigated together with the role of glide symmetry. Two waveguide structures have glide symmetry, and the irreducible Brillouin zone (BZ) is related to half of the period, leading to a wide band linearity, i.e., nondispersive, property of the dispersion diagram. The investigation on the modes with longitudinal electric field that can be excited shows that the bottom-top glide (BT glide) symmetric corrugated waveguide has a wide band interaction impedance, hence it is a good candidate for millimeter wave TWT amplifiers. Furthermore, the backward electromagnetic mode in such BT glide slow wave structure (SWS) is not $\textit{z}$ polarized, eliminating the risk of backward wave oscillations.
3 December 2024 in IEEE Transactions on Antennas and Propagation
A stacked array of two groove gap leaky wave antennas is proposed for synthesizing broad beam (or flat top) radiation patterns. Each leaky wave antenna is made with full control of the radiation angle and aperture field distribution thanks to the control of the complex wave number of the leaky mode. In addition, both leaky wave antenna exhibit Side Lobe Levels better than −20 dB and 90% radiation efficiency. A Power splitter inspired by a groove gap waveguide E-Plane Riblet coupler is utilized to obtain a 1-port network. In this device, the matching loads are not needed thanks to the antennas’ high efficiency and the coupler’s directivity. The design of a single layer LWA based on the design of a diverging beam with a real focus for flat top pattern synthesis is also shown, and the characteristics of both techniques are compared. The designed array of stacked antennas has been manufactured and measured, and the obtained results show a broad beam with high angular selectivity and almost constant gain across the designed angular region.
18 August 2021 in IEEE Transactions on Terahertz Science and Technology
When packaging large-width microwave integrated circuits, care has to be taken to avoid structures that could sustain unwanted oscillations. Unfortunately, this situation may not be attainable since large holding cavities are prone to support parasitic waveguide modes that could produce a feedback loop which, in turn, is especially dangerous in high-gain components with poor match with subsequent elements. This letter presents an scalable metasurface, implemented as a gap-waveguide perfect magnetic conductor, suitable to overcome this problem in millimeter- and submillimeter-band receivers. The proposed solution was integrated into a compact $W$ -band (75–110 GHz) receiver where a large chip-width amplifier was placed near a mixer, thus generating oscillations at high-gain levels compromising its operation at some frequencies. The metasurface was incorporated at the top of the amplifier's cavity where it did not only suppressed completely the oscillation, but also increased isolation between components. As a result, the receiver became fully operational as attested by measurements of its noise temperature at the compromised frequencies.
18 July 2024 in IEEE Transactions on Antennas and Propagation
This paper presents an experimental validation of a backscattering-protected bifilar edge line (BEL) constructed entirely by metallic materials. This waveguide relies on the principle of parity (P) time-reversal (T) duality (D) symmetry. In the ideal case, PTD symmetric structures have been theoretically demonstrated to be robust against backscattering for a certain class of discontinuities, namely those still respecting the PTD symmetry. The waveguide analysed here is constituted by a parallel plate waveguide (PPW) in which each of the two walls comprises two parts: a perfect electric conductor (PEC) and a perfect magnetic conductor (PMC) joint by an edge. On the two opposite walls, the faced boundary conditions exhibit a dual nature. The PMC is emulated by metallic short pillars (square cross-section pins). Two distinct pillar geometries are investigated for implementing the PMC. In the first case, the pillars of the top and bottom walls are aligned with each other along the propagation direction, whereas, in the second case, the pillars on the upper right wall are strategically shifted to control the dispersion of the mode supported by the structure. Numerical and experimental results are shown demonstrating the ability to confine the electromagnetic (EM) field in the proximity of the bifilar edge line over a large bandwidth, while maintaining the back-scattering protection in the 22 to 26.5 GHz band.
13 February 2024 in IEEE Antennas and Wireless Propagation Letters
A strategy based on the synthetic technique for the determination of the wavenumber dispersion diagram of modes in waveguides with glide symmetry is presented. The technique reconstructs the modal dispersion diagram from a number of resonance frequencies of a cavity made from the same guiding structure. The number of resonances required for periodic structures with glide symmetry is almost double of that for the nonglide case and the reason is here discussed, together with other issues related to the actual number of resonances that a cavity exhibits due to losses, excitation and cavity terminations. The proposed modification of the method is validated by using both simulations and experimental results.
27 February 2026 in IEEE Antennas and Wireless Propagation Letters
This paper presents a novel antenna design based on Groove Gap Waveguide (GGWG) technology with a reduced Radar Cross Section (RCS). To achieve this, GGWG technology is combined with printed circuit board (PCB) technology, enabling the integration of a metasurface (MTS) to minimize the RCS. The radiating elements are implemented as subarrays of patch antennas. The patch array is excited through transverse slots in the GGWG, while reflection-canceling posts (RCPs) are incorporated to enhance bandwidth and a new transition for central feeding is designed. The design is optimized for a central frequency of 28 GHz. A prototype of the designed antenna was fabricated, assembled, and experimentally measured. The measurement results demonstrate excellent performance, validating the proposed concept that can be extended to other types of antennas. To demonstrate the latter, a novel circularly polarized radiating element has also been explored.