5 November 2024 in IEEE Open Journal of the Communications Society
A Reconfigurable Intelligent Surface (RIS) consists of many small reflective elements whose reflection properties can be adjusted to change the wireless propagation environment. Envisioned implementations require that each RIS element be connected to a controller, and as the number of RIS elements on a surface may be on the order of hundreds or more, the number of required electrical connectors creates a difficult wiring problem. A potential solution to this problem was previously proposed by the authors in which “biasing transmission lines” carrying standing waves are sampled at each RIS location to produce the desired bias voltage for each RIS element. This paper presents models for the RIS elements that account for mutual coupling and realistic varactor characteristics, as well as circuit models for sampling the transmission line to generate the RIS control signals. The paper investigates two techniques for conversion of the transmission line standing wave voltage to the varactor bias voltage, namely an envelope detector and a sample-and-hold circuit. The paper also develops a modal decomposition approach for generating standing waves that are able to generate beams and nulls in the resulting RIS radiation pattern that maximize either the Signal-to-Noise Ratio (SNR) or the Signal-to-Leakage-plus-Noise Ratio (SLNR). The paper provides five algorithms, two for the case of the envelope detector, one for the sample-and-hold circuit, one for pursuing the global minimum for both circuits, and one for simultaneous beam and null steering. Extensive simulation results show that while the envelope detector is simpler to implement, the sample-and-hold circuit has substantially better performance and runs in substantially less time. In addition, the wave-controlled RIS is able to generate strong beams and deep nulls in desired directions. This is in contrast with the case of arbitrary control of each varactor element and idealized RIS models.
21 August 2023 in IEEE Transactions on Electron Devices
Focusing on traveling wave tube (TWT) applications, the interaction impedance between an electron beam and electromagnetic modes in three distinct, but related, corrugated waveguides that operate at millimeter waves is investigated together with the role of glide symmetry. Two waveguide structures have glide symmetry, and the irreducible Brillouin zone (BZ) is related to half of the period, leading to a wide band linearity, i.e., nondispersive, property of the dispersion diagram. The investigation on the modes with longitudinal electric field that can be excited shows that the bottom-top glide (BT glide) symmetric corrugated waveguide has a wide band interaction impedance, hence it is a good candidate for millimeter wave TWT amplifiers. Furthermore, the backward electromagnetic mode in such BT glide slow wave structure (SWS) is not $\textit{z}$ polarized, eliminating the risk of backward wave oscillations.
13 August 2025 in IEEE Open Journal of the Communications Society
A promising type of Reconfigurable Intelligent Surface (RIS) employs tunable control of its varactors using biasing transmission lines below the RIS reflecting elements. Biasing standing waves (BSWs) are excited by a time-periodic signal and sampled at each RIS element to create a desired biasing voltage and control the reflection coefficients of the elements. A simple rectifier can be used to sample the voltages and capture the peaks of the BSWs over time. Like other types of RIS, attempting to model and accurately configure a wave-controlled RIS is extremely challenging due to factors such as device non-linearities, frequency dependence, element coupling, etc., and thus significant differences will arise between the actual and assumed performance. An alternative approach to solving this problem is data-driven: Using training data obtained by sampling the reflected radiation pattern of the RIS for a set of BSWs, a neural network (NN) is designed to create an input-output map between the BSW amplitudes and the resulting sampled radiation pattern. This is the approach discussed in this paper. In the proposed approach, the NN is optimized using a Genetic Algorithm (GA) to minimize the error between the estimated and measured radiation patterns. The BSW amplitudes are then designed via Simulated Annealing (SA) to optimize a signal-to-leakage-plus-noise ratio measure by iteratively forward-propagating the BSW amplitudes through the NN and using its output as feedback to determine convergence. The resulting optimal solutions are stored in a lookup table to be used both as settings to instantly configure the RIS and as a basis for determining more complex radiation patterns.
13 February 2024 in IEEE Antennas and Wireless Propagation Letters
A strategy based on the synthetic technique for the determination of the wavenumber dispersion diagram of modes in waveguides with glide symmetry is presented. The technique reconstructs the modal dispersion diagram from a number of resonance frequencies of a cavity made from the same guiding structure. The number of resonances required for periodic structures with glide symmetry is almost double of that for the nonglide case and the reason is here discussed, together with other issues related to the actual number of resonances that a cavity exhibits due to losses, excitation and cavity terminations. The proposed modification of the method is validated by using both simulations and experimental results.
26 August 2020 in Revista Ontare
En este documento se presentan el análisis y los resultados relevantes relacionados con la caracterización de los conectores SMA acoplados a una línea de transmisión de 50 Ω. Dicha caracterización se llevó a cabo utilizando un analizador de espectros FSH8 Rohde & Schwarz, con el cual se midieron dos de sus parámetros S y se compararon con el comportamiento en simulación de la línea con y sin los conectores. El error relativo obtenido en cada caso evidencia algunos de los efectos encontrados por la influencia de los conectores y permite realizar un acercamiento al comportamiento esperado en este tipo de implementación. Por otra parte, también se puede concluir que los conectores SMA aportaron un corrimiento en frecuencia de la resonancia de la línea, así como un cambio en su atenuación, también se puede establecer que una calibración adecuada y completa de los puertos del equipo que se utilice en mediciones en altas frecuencias es fundamental para la obtención de resultados correctos y para descartar fuentes de eventuales errores. De igual forma, es viable reproducir desde la simulación los principales efectos que pueden tener los conectores utilizados en una medición de radiofrecuencia. Finalmente, dado que cada conector aporta errores particulares imposibles de predecir con certeza, es necesario el uso de técnicas de procesamiento adicionales que permitan minimizar estos errores.
1 January 2026 in IEEE Transactions on Plasma Science