23 July 2020 in Physical Review Letters
Energy recovery has been achieved in a multipass linear accelerator, demonstrating a technology for more compact particle accelerators operating at higher currents and reduced energy consumption. Energy delivered to the beam during the first four passes through the accelerating structure was recovered during four subsequent decelerating passes. High-energy efficiency was achieved by the use of superconducting accelerating cavities and permanent magnets. The fixed-field alternating-gradient optical system used for the return loop successfully transported electron bunches of 42, 78, 114, and 150 MeV in a common vacuum chamber. This new kind of accelerator, an eight-pass energy recovery linac, has the potential to accelerate much higher current than existing linear accelerators while maintaining small beam dimensions and consuming much less energy per electron.
27 May 2021 in Physical Review Accelerators and Beams
Quasimonochromatic x rays are difficult to produce above 100 keV, but have a number of uses in x-ray and nuclear science, particularly in the analysis of transuranic species. Inverse Compton scattering (ICS) is capable of fulfilling this need, producing photon beams with properties and energies well beyond the limits of typical synchrotron radiation facilities. We present the design and predicted output of such an ICS source at CBETA, a multiturn energy-recovery linac with a top energy of 150 MeV, which we anticipate producing x rays with energies above 400 keV and a collimated flux greater than photons per second within a 0.5% bandwidth. At this energy, the anticipated flux exceeds that attainable from storage ring sources of synchrotron radiation, even though CBETA is a significantly smaller accelerator system. We also consider the consequences of extending the CBETA ICS source performance to higher electron energies, exploring achievable parameters and applications for MeV-scale photons. We foresee that future energy-recovery linacs may serve as ICS sources, capable of providing high energy photons unavailable at synchrotron radiation facilities or photon beams above approximately 300 keV which outperform sources at synchrotron radiation facilities in both flux and average brilliance.
27 January 2021 in Physical Review Accelerators and Beams
Prior to establishing operation of the world’s first multiturn superconducting energy recovery linac, the Cornell-BNL energy recovery test accelerator was configured for one-turn energy recovery. In this setup, direct measurement of the beam loading in each of the main linac cavities demonstrated high energy recovery efficiency. Specifically, a total one-turn power balance efficiency of 99.4%, with per cavity power balances ranging from 99.2–99.8% was measured. When accounting for small particle losses occurring in the path length adjustment sections of the return loop, the per cavity power balances correspond to per cavity single particle energy recovery efficiencies ranging from 99.8 to 100.5%. A maximum current of , limited by the an incomplete radiation shielding installation around the main beam stop at the time of these measurements, was energy recovered.
23 January 2025 in Physical Review Accelerators and Beams
The maximum achievable beam current in an energy recovery linac (ERL) is often constrained by beam breakup (BBU) instability. Our previous research highlighted that filling patterns have a substantial impact on BBU instabilities in multipass ERLs. In this study, we extend our investigation to the eight-cavity model of the Powerful ERL for Experiment (PERLE). We evaluate its requirements for damping cavity higher order modes (HOMs) and propose optimal filling patterns and bunch timing strategies. Our findings reveal a significant new insight: while filling patterns are crucial, the timing of bunches also plays a critical role in mitigating HOM beam loading and BBU instability. This previously underestimated factor is essential for effective BBU control. We estimated the PERLE threshold current using both analytical and numerical models, incorporating the designed PERLE HOM dampers. During manufacturing, HOM frequencies are expected to vary slightly. Our study found no significant difference in BBU suppression for relative rms frequency jitters of 0.001, 0.002, and 0.005 for the same HOM. Introducing a jitter of 0.001 into our models, we found that the dampers effectively suppressed BBU instability, achieving a threshold current an order of magnitude higher than the design requirement. Our results offer new insights into ERL BBU beam dynamics and have important implications for the design of future ERLs.
4 September 2024 in arXiv
The maximum achievable beam current in an Energy Recovery Linac (ERL) is often constrained by Beam Breakup (BBU) instability. Our previous research highlighted that filling patterns have a substantial impact on BBU instabilities in multi-pass ERLs. In this study, we extend our investigation to the 8-cavity model of the Powerful ERL for Experiment (PERLE). We evaluate its requirements for damping cavity Higher Order Modes (HOMs) and propose optimal filling patterns and bunch timing strategies. Our findings reveal a significant new insight: while filling patterns are crucial, the timing of bunches also plays a critical role in mitigating HOM beam loading and BBU instability. This previously underestimated factor is essential for effective BBU control. We estimated the PERLE threshold current using both analytical and numerical models, incorporating the designed PERLE HOM dampers. During manufacturing, HOM frequencies are expected to vary slightly, with an assumed RMS frequency jitter of 0.001 between cavities for the same HOM. Introducing this jitter into our models, we found that the dampers effectively suppressed BBU instability, achieving a threshold current an order of magnitude higher than the design requirement. Our results offer new insights into ERL BBU beam dynamics and have important implications for the design of future ERLs.