1 January 2016 in Express Polymer Letters
Current challenges highlight the need for polymer research using renewable natural sources as a substitute for petroleum-based polymers. The use of polyols obtained from renewable sources combined with the reuse of industrial residues such as lignin is an important agent in this process. Different compositions of polyurethane-type materials were prepared by combining technical Kraft lignin (TKL) with castor oil (CO) or modified castor oil (MCO1 and MCO2) to increase their reactivity towards diphenylmethane diisocyanate (MDI). The results indicate that lignin increases the glass transition temperature, the crosslinking density and improves the ultimate stress especially for those prepared from MCO2 and 30% lignin content from 8.2 MPa (lignin free) to 23.5 MPa. Scanning electron microscopy (SEM) micrographs of rupture surface after uniaxial tensile tests show ductile-to-brittle transition. The results show the possibility to develop polyurethane-type materials, varying technical grade Kraft lignin content, which cover a wide range of mechanical properties (from large elastic/low Young modulus to brittle/high Young modulus polyurethanes)
26 April 2016 in The Journal of Adhesion
This work aimed to evaluate the influence of the aliphatic and aromatic hydroxyl level on the polyurethane adhesive property and chemical structure. This adhesive was obtained through the reaction of technical Kraft lignin (TKL) as polyol with diphenylmethane diisocyanate (MDI). Thus, lignopolyurethane adhesives were obtained with NCO:OH ratios of 0.8:1.0, 0.9:1.0, 1.0:1.0, 1.1:1.0, and 1.2:1.0. Initially only the TKL aliphatic hydroxyl level was taken into consideration in the stoichiometry in order to define the mass ratio between MDI and polyol. Subsequently, lignopolyurethane adhesive was obtained using the same NCO:OH ratios considering TKL total hydroxyls’ level, and aromatic and aliphatic hydroxyls. The chemical structures of the synthesized adhesives were analyzed by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (13C NMR). The mechanical property of the adhesively bonded joints, comprising wood substrates and synthesized adhesives, was measured using single lap shear tests. Results illustrated that by increasing the NCO:OH ratio, there is an increase in the free isocyanate content leading to higher shear strength values. Higher free isocyanate content leads to MDI dimer formation in the lignopolyurethane structure.
1 September 2019 in International Journal of Adhesion and Adhesives
1 January 2019 in Materials Research
Low surface energy and poor adhesion are well-known characteristics of polypropylene (PP). Surface treatments such as plasma, corona, and laser are usually applied to overcome these limitations. However, current studies highlight the incorporation of hydrophilic or amphiphilic polymers into hydrophobic low-surface-energy polymers as an alternative for increasing surface energy and thus improving adhesion. Lignin could be a promising amphiphilic polymer for use in increasing surface energy. In this work, PP/kraft lignin composites were obtained by incorporating up to 5 wt% of kraft lignin (KL) into a PP matrix. Corona treatment was applied to pristine PP and composites surfaces. Contact angle measurements and peeling tests were carried out to investigate the effects of KL incorporation and corona treatment on the surface energy and the mechanical strength of adhesion. Differential scanning calorimetry (DSC) was used to evaluate the PP’s crystallinity index and recrystallization temperature and to dismiss their effects on the surface energy changes. Scanning electron microscopy (SEM) was applied to investigate the lignin dispersion. The results show that KL incorporation has potential as a method to improve the surface energy of PP, improve its poor adhesion, and enhance the effects of corona treatment.
29 January 2018 in The Journal of Adhesion
Polyurethane is one of the most versatile and commonly applied polymers in the world. Its properties are strongly dependent on the polyol/isocyanate structures and NCO:OH ratio, among other parameters. Additionally, the polyol structure is affected by the catalyst used for the reaction and production. The catalyst may indirectly affect the curing kinetics and mechanical strength of the PU, due to changes of polyol properties. This work evaluates the effects of two catalysts on the polyol structure and thus the effect of these polyol changes on the curing kinetics and mechanical strength of a PU adhesive. Two polyols were synthetized using the same hydroxyl-containing molecules derived from renewable natural sources, but with different types of catalysts (based on Sn or Li/Ti). The synthesized polyols were separately mixed with diphenylmethane diisocyanate in a 1.1:1 ratio of NCO to OH to form two bio-based PUs. The polyols were investigated by Fourier transform infrared (FTIR) spectroscopy, which showed the occurrence of some changes in the chemical groups of the polyol structure for both catalysts, as well as an influence on the curing kinetics. The mechanical behavior of the PU adhesives was characterized by dynamic mechanical analysis (DMA) and peeling tests. The results show a higher curing rate and higher peeling strength for the PU adhesives obtained using the Sn-based catalyst; both adhesives showed cohesive failure.
2 March 2017 in Journal of Applied Polymer Science