5 February 2019 in Nature Reviews Materials
27 November 2017 in Advanced Functional Materials
Lead halide perovskite quantum dots (QDs) possess color‐tunable and narrow‐band emissions and are very promising for lighting and display applications, but they suffer from lead toxicity and instability. Although lead‐free Bi‐based and Sn‐based perovskite QDs (CsSnX3, Cs2SnX6, and (CH3NH3)3Bi2X9) are reported, they all show low photoluminescence quantum yield (PLQY) and poor stability. Here, the synthesis of Cs3Bi2Br9 perovskite QDs with high PLQY and excellent stability is reported. Via a green and facile process using ethanol as the antisolvent, as‐synthesized Cs3Bi2Br9 QDs show a blue emission at 410 nm with a PLQY up to 19.4%. The whole series of Cs3Bi2X9 (X = Cl, Br, and I) QDs by mixing precursors can cover the photoluminescence emission range from 393 to 545 nm. Furthermore, Cs3Bi2Br9 QDs show excellent photostability and moisture stability due to the all‐inorganic nature and the surface passivation by BiOBr, which enables the one‐pot synthesis of Cs3Bi2Br9 QD/silica composite. A lead‐free perovskite white light‐emitting diode is fabricated by simply combining the composite of Cs3Bi2Br9 QD/silica with Y3Al5O12 phosphor. As a new member of lead‐free perovskite QDs, Cs3Bi2Br9 QDs open up a new route for the fabrication of optoelectronic devices due to their excellent stability and photophysical characteristics.
23 December 2022 in Science
The development of highly stable and efficient wide-bandgap (WBG) perovskite solar cells (PSCs) based on bromine-iodine (Br–I) mixed-halide perovskite (with Br greater than 20%) is critical to create tandem solar cells. However, issues with Br–I phase segregation under solar cell operational conditions (such as light and heat) limit the device voltage and operational stability. This challenge is often exacerbated by the ready defect formation associated with the rapid crystallization of Br-rich perovskite chemistry with antisolvent processes. We combined the rapid Br crystallization with a gentle gas-quench method to prepare highly textured columnar 1.75–electron volt Br–I mixed WBG perovskite films with reduced defect density. With this approach, we obtained 1.75–electron volt WBG PSCs with greater than 20% power conversion efficiency, approximately 1.33-volt open-circuit voltage ( V oc ), and excellent operational stability (less than 5% degradation over 1100 hours of operation under 1.2 sun at 65°C). When further integrated with 1.25–electron volt narrow-bandgap PSC, we obtained a 27.1% efficient, all-perovskite, two-terminal tandem device with a high V oc of 2.2 volts.
13 September 2017 in Journal of the American Chemical Society
High-quality metal halide perovskite single crystals have low defect densities and excellent photophysical properties, yet thin films are the most sought after material geometry for optoelectronic devices. Perovskite single-crystal thin films (SCTFs) would be highly desirable for high-performance devices, but their growth remains challenging, particularly for inorganic metal halide perovskites. Herein, we report the facile vapor-phase epitaxial growth of cesium lead bromide perovskite (CsPbBr3) continuous SCTFs with controllable micrometer thickness, as well as nanoplate arrays, on traditional oxide perovskite SrTiO3(100) substrates. Heteroepitaxial single-crystal growth is enabled by the serendipitous incommensurate lattice match between these two perovskites, and overcoming the limitation of island-forming Volmer–Weber crystal growth is critical for growing large-area continuous thin films. Time-resolved photoluminescence, transient reflection spectroscopy, and electrical transport measurements show that the CsPbBr3 epitaxial thin film has a slow charge carrier recombination rate, low surface recombination velocity (104 cm s–1), and low defect density of 1012 cm–3, which are comparable to those of CsPbBr3 single crystals. This work suggests a general approach using oxide perovskites as substrates for heteroepitaxial growth of halide perovskites. The high-quality halide perovskite SCTFs epitaxially integrated with multifunctional oxide perovskites could open up opportunities for a variety of high-performance optoelectronics devices.
24 July 2019 in ACS Central Science
The stability and formation of a perovskite structure is dictated by the Goldschmidt tolerance factor as a general geometric guideline. The tolerance factor has limited the choice of cations (A) in 3D lead iodide perovskites (APbI3), an intriguing class of semiconductors for high-performance photovoltaics and optoelectronics. Here, we show the tolerance factor requirement is relaxed in 2D Ruddlesden–Popper (RP) perovskites, enabling the incorporation of a variety of larger cations beyond the methylammonium (MA), formamidinium, and cesium ions in the lead iodide perovskite cages for the first time. This is unequivocally confirmed with the single-crystal X-ray structure of newly synthesized guanidinium (GA)-based (n-C6H13NH3)2(GA)Pb2I7, which exhibits significantly enlarged and distorted perovskite cage containing sterically constrained GA cation. Structural comparison with (n-C6H13NH3)2(MA)Pb2I7 reveals that the structural stabilization originates from the mitigation of strain accumulation and self-adjustable strain-balancing in 2D RP structures. Furthermore, spectroscopic studies show a large A cation significantly influences carrier dynamics and exciton–phonon interactions through modulating the inorganic sublattice. These results enrich the diverse families of perovskite materials, provide new insights into the mechanistic role of A-site cations on their physical properties, and have implications to solar device studies using engineered perovskite thin films incorporating such large organic cations.
20 September 2017 in Chemistry of Materials